Driveline vibration after a lift comes from steep u-joint angles. Compare a transfer case drop, SYE, CV shaft and pinion shims, with fixes by…
Leaf Spring Axle Shim
Showing 13–24 of 24 resultsSorted by popularity
-
-
-
-
-
Leaf Spring Axle Shim
Rubicon Express Degree Shim 2.5 Inch Wide X 6 Degree Steel – RE1468
- Rubicon Express RE1468 6 degree steel shim for leaf springs
- Fits leaf springs that are 2.5 inches wide
- Designed to become part of the spring pack rather than float on the perch
- Can be installed at the front or rear to set pinion angles
- Center pins not included; sold in pairs
SKU: R/ERE1468 -
-
Leaf Spring Axle Shim
Rubicon Express Degree Shim 2.5 Inch Wide X 2 Degree Steel – RE1464
- Solid steel shim with a 2 degree angle for leaf springs 2.5 inches wide
- Used front or rear to set pinion angles
- Becomes part of the spring pack, so it does not come loose
- Center pins are not included
- Brand Rubicon Express, part number RE1464
SKU: R/ERE1464 -
-
Leaf Spring Axle Shim
Rubicon Express Degree Shim 2.5 Inch Wide X 8 Degree Steel – RE1469
- 8 degree steel shim for 2.5 in wide leaf springs
- Sold as a pair; center pins not included
- Designed to sit inside the spring pack
- Usable at the front or rear to set pinion angle
- Part RE1469, UPC 614901438406
SKU: R/ERE1469 -
What an axle shim does
On a leaf-spring vehicle, the axle sits on the spring pack and the angle of the axle housing is set by how the spring pad rests on the spring. The pinion at the front of the differential must point close to the driveshaft's angle at the transmission or transfer case to keep the universal joints running smoothly. A tapered shim goes between the spring and the axle perch, rotating the axle housing slightly. A few degrees at the axle can make the difference between a smooth driveline and a vibration that is felt at highway speed.
When shims are used
- After a lift, particularly with lift blocks or new springs that change the pinion angle.
- When a driveshaft vibration appears at certain speeds.
- When a rear axle has rotated under load, a condition called axle wrap, and the angle needs resetting.
- When adjusting pinion angle on a front leaf-spring axle, for example to set caster.
How to choose a shim
The shim must match the spring width. Listings are commonly 2 inches or 2.5 inches wide, and using the wrong width leaves the spring unsupported. Next, pick the degree. The right angle depends on how much your suspension changed the pinion position, which is measured with an angle finder, and the manufacturer's instructions can guide the starting point. Common tapers range from about 1 or 2 degrees up to 8 degrees. A shim that is too large can bring the pinion angle past the ideal. Many owners measure first and choose the closest option.
Specs to compare
- Spring width and degree of taper.
- Material: aluminum is lighter, steel is stronger and stiffer.
- Center pin hole size, since the shim must fit around the spring center pin, and some accept a larger pin.
- Whether the listing sells one shim or a pair, since you normally need one for each side.
Installation and safety notes
This is suspension work, so support the vehicle on jack stands rated for the load, and do not rely on a jack alone. Make sure the center pin engages the axle perch properly, torque the U-bolts evenly and to specification, and recheck them after a short drive. After installation, have the driveline angles and alignment checked. A longer center pin may be needed with a thicker shim.
Confirm fitment for your exact year, make and model, and read the manufacturer's specifications before choosing.
Measuring before you buy
A short measuring session saves time. With the vehicle on level ground at normal ride height, use a digital angle finder to read the angle of the pinion flange and the driveshaft. Record both numbers. Remember that the pinion rotates upward under acceleration, so many setups aim for the pinion to sit slightly below the driveshaft angle at rest, within the manufacturer's guidance.
For two-piece driveshafts or four-link setups, the target angles differ, so read the instructions for your suspension. Shims move the angle in fixed steps, so you may find that two sizes give a similar result, in which case consider which one lines up better with the other changes planned. After installing, road test, listen for vibration at various speeds and recheck the angle under the new condition. Retighten the U-bolts after the first drive and again after a few hundred miles.
Related guides
- Driveline Vibration After a Lift: Transfer Case Drop or SYE?
Popular Leaf Spring Axle Shim brands
Leaf Spring Axle Shim FAQ
How do I know what degree shim I need?
Measure the pinion angle and driveshaft angle with an angle finder, and compare them with the manufacturer's recommended working angles. The shim should bring them closer to a matched, slightly opposing relationship. Confirm fitment for your vehicle.
Do I need one shim or two?
Typically one per spring, so a pair for an axle. Some listings are sold individually and others as a pair, so check the quantity on the product page before choosing.
What width shim do I need?
Match the shim width to your leaf spring width, most commonly 2 inches or 2.5 inches. A shim that is too narrow does not fully support the spring. Measure your spring pack or check the factory specifications.
Can shims fix a vibration after a lift?
They can if the cause is a pinion angle that changed with the lift. Vibrations can also come from worn U-joints, driveshaft length or balance, so check those too. Measure angles before changing parts.





