Select your vehicle

Warrior Leaf Spring Shims – 800050

Warrior

Shop Warrior Leaf Spring Axle Shim on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Pair of 2 degree leaf spring axle shims, 2″ wide
  • Corrects pinion and caster angles on leaf sprung Jeeps and trucks
  • Steel, American-made, counter-bored for a 5/16″ cross-pin
  • Warrior part number 800050

Description

Overview

The Warrior 800050 is a pair of 2 degree leaf spring axle shims, 2″ wide, made in the USA from steel, for fine corrections to the pinion and caster angles of a leaf sprung Jeep or truck.

Warrior builds the shims to bolt into the leaf spring pack permanently, held by the leaf’s own cross-pin. The cross hole is counter-bored against the angled face, which Warrior says spreads clamping force evenly over the pin head, and the steel body is meant to keep the shim intact under heavy loads.

This 2 degree shim is the gentler of the angles, a good choice when only a small change is needed. It is the version without center pins.

A small angle correction can be enough to quiet a driveline vibration after a modest lift, since the pinion angle only needs to move a few degrees to line up the joints.

Key features

  • 2 degree leaf spring axle shim
  • 2″ wide
  • American-made from high quality steel
  • Counter-bored cross hole spreads clamping force across the pin
  • Accepts a 5/16″ cross-pin
  • Easily drilled for larger pins
  • Supplied as a pair
  • Version without center pins

Pinion angle and shim use

Leaf spring axle shims change the angle of the axle relative to the driveshaft or caster setting, so they are used for small corrections rather than large changes. After a lift, a small angle error can cause vibration at speed, and a shim can bring the joints back into a more even relationship. The right angle depends on the existing setup, so measure before choosing a shim.

Once the shim is installed, the angle should be checked again with the vehicle at its normal ride height and load. Pay attention to the cross-pin, the spring pack and the axle perch, since a shim that moves can change the geometry. Inspect the shims and pins during regular service, and replace any that show cracks, wear or deformation.

  • Measure the existing angle before choosing a shim
  • Re-check pinion and caster angles after installation
  • Inspect cross-pins and shims during regular service

Specifications

Brand Warrior
Part number 800050
UPC 634146800509
Part type Leaf spring axle shims
Angle 2 degree
Width 2″
Material Steel, American-made
Cross-pin size Accepts 5/16″ cross-pin; can be drilled for larger pins
Cross hole Counter-bored
Center pins Without center pins
Quantity Pair
Warrior fitment label Universal fit

Vehicle fitment

Warrior labels the 800050 shims universal fit for leaf sprung Jeeps and trucks. They are not matched to a named vehicle, year range or chassis code.

Make sure your axle sits on a leaf spring pack, that the spring is 2 inch wide, and that the cross-pin matches before ordering. Confirm fit for your vehicle’s year, model and trim before ordering.

Installation notes

Each shim stays on the spring pack for good once the cross-pin is through it. Because this is the without-center-pins version, confirm that your springs match, and plan to drill the hole if you use a pin larger than 5/16″.

What’s included

One pair of 2 degree leaf spring shims.

SKU: W/I800050 Category:

Specification

Shipping weight 3.00 lbs
Package dimensions 4.00 × 4.00 × 4.00 in
brands

Questions & Answers

What angle are the Warrior 800050 shims?

The Warrior 800050 shims are 2 degree. They are 2" wide, and they make a small correction to the pinion or caster angle on a leaf sprung vehicle.

What cross-pin size do the 800050 shims take?

They accept a 5/16 inch cross-pin. The cross holes are counter-bored and can be drilled out to fit larger pins.

Are the Warrior 800050 shims universal?

Warrior labels them universal for leaf sprung Jeeps and trucks, but no specific vehicles are listed, so check your spring width, cross-pin and needed angle.

Is the 800050 sold in pairs?

Yes. The shims are supplied as a pair, so a single set covers both of the leaf spring packs on one axle.

Do leaf spring shims need re-checking after install?

Yes. Re-check the pinion angle and driveline joint angles after installation, and inspect the cross-pin for wear. A shim that shifts can change the geometry, so check it again after the first few drives.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Warrior Leaf Spring Axle Shim on Amazon