Performance Steering Upgrades
Performance steering upgrades cover the parts that sharpen steering response and cope with the stress of lifts and larger tires, including tie rod ends, drag links, pitman arms, high steer kits, and steering knuckles. Brands here include Moog, Fabtech, PSC Steering, TeraFlex, and Tuff Country. Open a product page for fitment and part numbers, then compare the products below.

Big tires and lifts load the steering far more than the factory planned. Heavier linkage, corrected geometry and stronger pumps keep the wheel steady on the highway and keep the tie rod from folding on a rock. This section covers those upgrades for Jeeps, Toyotas, Ram and Ford trucks.
Tie rod parts are the largest group, from direct-fit Moog ends to heavy-duty threaded ends for built axles. The steering gear group holds drag links, pitman arms and complete high steer kits. Knuckle parts include studs and full replacement knuckles. A small power steering group covers pump conversions, pulleys, reservoir parts and valves, plus a few columns, shafts and steering blocks for older trucks.
Shop steering upgrades by type
Popular steering upgrades
-
Steering Knuckles & Components
Trail Gear Magnum Knuckle Stud – 140171-1-KIT
- Trail Gear Magnum knuckle stud, part 140171-1-KIT, with an 8mm hex head
- Made from ARP 2000 material and hardened to 220,000 PSI
- Longer than stock to accommodate aftermarket steering arms
- Designed to be stronger than stock replacement Toyota knuckle studs
SKU: TGI140171-1-KIT -
Steering Knuckles & Components
Dana Spicer Dana Ultimate 60 Steering Knuckle (Driver Side) – 2023567
Steering Knuckles & ComponentsDana Spicer Dana Ultimate 60 Steering Knuckle (Driver Side) – 2023567
- Fits 2007–2018 Jeep Wrangler (JK), 2-door and 4-door, per the manufacturer fitment list
- Dana Spicer Dana Ultimate 60 steering knuckle, driver side (front left), part number 2023567
- Modified replacement knuckle; usable in Dana’s Builder Axle program
- Direct fit
SKU: D/S2023567 -
Steering Gear Box & Components
Trail Gear High Steer Kit – 302523-1-KIT
- Crossover high steer kit for rock crawling with forged steering arms, pitman arm, rods and rod ends
- Built for the 1979-1995 Toyota Pickup and the 1985-1995 4Runner
- Flat steering arm kit; custom mounting hardware is not included
- Heavy-duty .250 wall steering rods
SKU: TGI302523-1-KIT -
Steering Gear Box & Components
Mountain Off Road Enterprises Heavy-Duty Drag Link – 9927
- Heavy-duty drag link for 1982-1986 Jeep CJ5, CJ7 and Scrambler
- 1-inch D.O.M. steel tube, .219 wall, with 5/8 threaded ends
- Teflon / Kevlar lined, self lubricating rod ends
- Jam nuts and grade 8 hardware included; stock hole must be drilled to 5/8 inch
SKU: MRE9927
Steering linkage and pump reference
Specs pulled from the listed parts, plus the layout terms you will see in steering kit descriptions. Confirm thread, taper and position on each product page before ordering.
Linkage specs in this section
| TeraFlex HD tie rod end (TJ/LJ) | 7/8"-18, left-hand thread, small taper |
|---|---|
| MORE drag link (CJ5/CJ7) | 1" DOM tube, .219" wall, 5/8" ends |
| Moog inner drag link (Super Duty) | 2011–2016 F-250/F-350, straight pitman arm |
| Moog inner tie rod (Ram 1500) | Forged one-piece, sold individually |
| Moog outer tie rod end (Ram 1500) | Left or right side, sold individually |
Power steering parts
| JL pump conversion (2018–2019) | Replaces the OEM electro-hydraulic pump |
|---|---|
| JL conversion requirement | Tazer JL programmer needed |
| Anti-splash valve | 6 PSI relief, for remote reservoir systems |
| Pump pulley | 6.0" single groove V-belt, Type II/CBR/CBX |
| Reservoir clip | 4.0L Jeeps: 1991–1995 Wrangler, ZJ, Comanche |
Steering layouts compared
| Where the links sit | Main benefit | |
|---|---|---|
| Stock low steer | Below the knuckle arms | Factory geometry, easy parts |
| Flip kit | Drag link moved above the arm | Levels the drag link after a lift |
| High steer | Arms bolted on top of the knuckles | Most rock clearance, flatter angles |
| Crossover | Drag link runs to the far knuckle | Less bump steer on solid axles |
What to match when ordering
- Position: inner or outer, driver or passenger side
- Thread size and direction (left-hand or right-hand)
- Taper size at the knuckle or pitman arm (small or large)
- Pitman arm style the link is built for (straight or drop)
- Axle and drivetrain: 2WD or 4WD, axle model
- Sold individually or as a pair
Knuckles, blocks and columns
- Dana Ultimate 60 knuckles for 2007–2018 JK, sold by side
- Hex-head knuckle studs for Trail Gear Magnum knuckles
- Dana 44 steering block for Dodge W-series, 3-bolt open knuckle only
- Six-position tilt column for 1948–1956 Chevrolet trucks and early Fords
- High steer kit for 1979–1995 Toyota Pickup and 1985–1995 4Runner
Steering parts are safety critical. Torque tapered studs to the maker's figure, reinstall cotter pins, and get an alignment after any linkage change.
All Performance Steering Upgrades 96 parts
-
-
-
-
-
Steering Gear Box & Components
Trail Gear High Steer Kit – 302523-1-KIT
- Crossover high steer kit for rock crawling with forged steering arms, pitman arm, rods and rod ends
- Built for the 1979-1995 Toyota Pickup and the 1985-1995 4Runner
- Flat steering arm kit; custom mounting hardware is not included
- Heavy-duty .250 wall steering rods
SKU: TGI302523-1-KIT -
-
Tie Rod Assemblies & Components
TeraFlex TJ HD High Steer Aluminum Tie Rod Kit with Stock Taper Tie Rod Ends – 4920255
Tie Rod Assemblies & ComponentsTeraFlex TJ HD High Steer Aluminum Tie Rod Kit with Stock Taper Tie Rod Ends – 4920255
- HD high steer tie rod kit in 1-1/2″ hexagon 6061 T6 aluminum
- Stock taper tie rod ends with one-ton joint ends
- Fits 1997-2006 Jeep Wrangler TJ and 2004-2006 Wrangler Unlimited LJ
- Intended for use with the TeraFlex Dana 30 High Steer Knuckle
SKU: TER4920255 -
What counts as a steering upgrade
Lifting a vehicle or fitting larger tires changes steering geometry and adds load to every link in the system. Upgrades in this category address that. Typical parts include inner and outer tie rod ends, heavy-duty drag links, drop pitman arms, high steer kits that move the tie rod above the knuckle, flip kits that correct drag link angle, steering knuckles, and power steering components such as reservoir clips and anti-splash valves.
Matching parts to the problem
- Wandering or loose steering after a lift: replace worn tie rod ends and check the drag link and track bar angles.
- Bump steer on a lifted solid-axle vehicle: a drop pitman arm or drag link flip kit helps restore a level drag link.
- Bent tie rods on the trail: a high steer kit or heavier-wall tubes tuck the linkage out of harm.
- Worn ball joints or damaged knuckles: a replacement knuckle may be a better answer than patching the old one.
Specs to compare
Look at the position listed on the product page, such as front inner, front outer, driver side, or passenger side. Note whether a part is sold individually or as a pair, and whether the listing is a direct replacement or modified design. For adjustable or heavy-duty linkage, compare tube diameter and wall thickness, joint type, and whether the end uses a tapered stud that fits your knuckle. Greasable joints are easier to maintain than sealed ones.
Installation and safety
Steering parts are safety critical. Tapered studs must be seated and torqued to the manufacturer specification, and cotter pins or nylon-insert locknuts must be reinstalled. Any change to tie rods, drag links, or knuckles calls for a professional alignment afterward. If you are not experienced with steering work, have the parts installed by a qualified shop.
Confirming fitment
Steering parts vary widely by year, axle, and drivetrain. Confirm fitment for your exact year, make, and model, including 2WD or 4WD, and check the manufacturer specifications. Combining parts from different brands can create clearance or geometry problems, so use components designed to work together.
Finally, inspect rubber boots on joints at every oil change. A torn boot lets dirt in and shortens joint life, and catching it early is far cheaper than replacing a damaged tie rod or knuckle later.
Inspection and common pairings
Check steering every time you change oil. With the front end supported and the wheels off the ground, grip each tire at nine and three o'clock and look for play at the tie rod ends and drag link joints, then check the pitman arm nut and the steering box mounting bolts. Steering upgrades work best when matched. A drop pitman arm pairs with a drag link flip kit, and heavier tie rod and drag link assemblies pair with a track bar bracket and frame brace when the lift raises the axle. Moog-style replacement ends suit a stock-geometry repair, while a high steer system suits heavy trail use. Avoid mixing joint sizes, because a mismatched tapered stud will not seat.
Popular Performance Steering Upgrades brands
- Moog (37)
- Trail Gear (8)
- TeraFlex (7)
- Fabtech (6)
- PSC Steering (6)
- Crown Automotive (5)
- Tuff Country (4)
- Rough Country (4)
- Dana Spicer (4)
- Skyjacker (3)
- Pro Comp Suspension (3)
- Borgeson Steering (2)
Performance Steering Upgrades FAQ
How do I know if my tie rod ends are worn?
Signs include play in the steering wheel, clunking over bumps, uneven tire wear, and wandering at speed. A shop can check by wiggling the wheel with the vehicle lifted. Replace worn ends in time, since a failed tie rod causes loss of steering.
What does a drop pitman arm do?
A drop pitman arm lowers the end of the arm so the drag link sits closer to level on a lifted vehicle. This can reduce bump steer. Choose one designed for your steering box and lift height.
Do I need an alignment after replacing tie rods?
Yes. Tie rod changes alter toe, and a professional alignment sets toe, camber, and caster correctly. Skipping it can cause rapid tire wear and poor handling.
What is a high steer kit?
A high steer kit moves the tie rod above the steering knuckle instead of in front or behind it. That raises it out of the way of rocks and can improve geometry, but it typically requires special knuckle arms and professional setup.



















