Select your vehicle
-13%
, ,

TeraFlex Heavy-duty Tie Rod End – 4920221

TeraFlex

  • Heavy-duty tie rod end, left-hand thread, small taper
  • 7/8 inch x 18 TPI
  • For Wrangler TJ and LJ, supplied individually

Purchase through Amazon

Orders are placed, shipped and supported through Amazon, with Amazon’s checkout, delivery options and return policy.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

Description

Overview

The TeraFlex heavy-duty tie rod end 4920221 (TER4920221) is a left-hand thread, small-taper tie rod end with a 7/8 inch x 18 TPI thread for the Jeep Wrangler TJ and LJ. It is supplied individually.

TeraFlex built its heavy-duty ends around a one-ton joint end. The stock Jeep taper, as on this part, fits Dana 30 knuckle holes.

Tie rods commonly pair a right-hand and a left-hand end, so this left-hand version is the counterpart to TeraFlex’s right-hand part.

The 7/8 inch x 18 TPI thread size is shared with the right-hand versions TeraFlex lists, so the thread direction and taper are what set the parts apart.

Key features

  • One-ton joint end
  • Left-hand thread
  • Small taper
  • 7/8 inch x 18 TPI
  • Supplied individually

Tie rod replacement tips

A tie rod end is a wear part that takes steering load and absorbs trail shock. When one end fails, the wheel can toe in or out, which makes the vehicle wander and wears the tire unevenly. Replacing a worn end is usually quicker than rebuilding the linkage, but the new end has to match the taper, thread and knuckle type already on the vehicle.

Thread direction matters. A left-hand end must be installed on the side that threads into the tie rod sleeve in the correct way, so mark the position of the old end before removing it. Set the length to the same reference as the old end, then have toe checked. Tighten the jam nut once the toe is set and recheck it after the first few drives on rough ground.

Pair the new end with its counterpart on the other side when possible, so steering stays even and the joints wear at the same rate.

  • Measure or mark the old end length before removal
  • Check the boot and joint for play after install
  • Set toe and recheck it after the first drives
  • Inspect the knuckle and steering arm for wear

Specifications

Brand TeraFlex
Part number TER4920221
Thread direction Left hand
Thread size 7/8 inch x 18 TPI
Taper Small
Quantity One

Vehicle fitment

It fits the 1997-2006 Jeep Wrangler (TJ) and the 2004-2006 Wrangler (LJ).

For larger 60-type knuckles, TeraFlex offers a large-taper end instead. Confirm your vehicle’s year, model and trim before ordering.

What’s included

One tie rod end.

Fitment

VehicleYearsTrims
Jeep Wrangler (LJ)2004–2006Unlimited, Unlimited Rubicon
Jeep Wrangler (TJ)1997–2006Rubicon, SE, Sahara, Sport, X

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

What thread does the TeraFlex 4920221 have?

It has a left-hand thread, 7/8 inch x 18 TPI, with a small stock-style taper, supplied individually as a heavy-duty tie rod end.

What knuckle does the small taper fit?

The stock-style small taper fits Dana 30 knuckle holes. Larger 60-type knuckles need the large-taper version of the end instead, so check the knuckle type before ordering.

Is the 4920221 sold as a pair?

No. It is supplied individually, with one tie rod end. A tie rod normally needs one left-hand and one right-hand end, so check what your linkage needs.

Can I replace just one tie rod end?

Yes, a single end can be replaced, but the other end may be worn to a similar point. Check both ends for play, and confirm the new end matches the taper, thread and knuckle type already on the vehicle before installation.