Fabrication & Tools
Showing 433–444 of 504 resultsSorted by popularity
-
-
Spindle Nut Socket
Omix-ADA Spindle Nut Socket – 16711.01
- Omix-ADA spindle nut socket for Dana 25, 27 and 30 front axles
- 2-1/16 inch thin wall deepwell spindle nut socket
- Part number 16711.01 from Omix-ADA
- Direct OE replacement built to original specifications, with limited five year warranty coverage
SKU: OAI16711.01 -
-
Shock Mounts
California Supertrucks Shock Mounting Kit – CSS-C33-4
- California Super Trucks CSS-C33-4 single shock mounting kit
- Adds brackets for 2 or 3 shocks per vehicle corner
- Designed for use with part number CSS-C3-15
- Direct fit; confirm your year, model and trim before ordering
SKU: CSTCSS-C33-4 -
Gussets & Tabs
Artec Dual 4-link Bracket – BR1013
- Universal dual 4-link bracket set, supplied as a pair
- Upper and lower frame mounts with 2 brackets included
- 1/4 inch thick mild steel, 2.65 inch joint mounting width
- 2.625 inch mounting width with 9/16 inch bolt hole for cartridge joints
- Rod ends are not included
SKU: A/IBR1013 -
Gussets & Tabs
Artec Heavy Duty Stock Tracbar Bracket – JK4407
- Stock front tracbar bracket for Dana 30 or Dana 44 JK axles
- 1/4 inch mild steel with a bare steel finish
- Maintains the factory sway bar mount location
- For 2 and 4-door models as a stock tracbar upgrade
- Welding and general fabrication required
SKU: A/IJK4407 -
Gussets & Tabs
Artec Dana 30 HD Lower Control Arm Brackets – TJ3011
- Artec Industries TJ3011 lower control arm brackets for Dana 30 axles, supplied as a pair
- Made from 1/4 inch steel plate with 2.625 inch mounting width
- Laser etched horseshoe around the CAM bolt with factory alignment lines
- Wraps the axle tube further than the factory bracket for added weld area
SKU: A/ITJ3011 -
-
What you will find here
Fabrication and tools covers the small parts that custom suspension and chassis work depends on. Rod ends and flex joints let links articulate, tube adapters join tubing to those joints, gussets and tabs reinforce brackets, and perches and shock mounts attach springs and shocks to axles and frames. Specialty tools such as joint presses, torsion key unloaders, spindle nut sockets and installation tools round out the category.
Rod ends and flex joints
Johnny Joint style flex joints use a bushing in a threaded housing, usually with urethane, and allow articulation while absorbing vibration. Heim joints, often called rod ends, use a spherical ball and are more rigid and precise, but they transmit more noise and need regular inspection. Left-hand and right-hand threaded ends, paired with jam nuts, let you adjust link length without removing the link. Misalignment spacers let a joint swing through its full range without binding.
Specs to match
- Thread size and direction: for example 3/4 inch versus 1-1/4 inch, left or right hand.
- Housing outside diameter and mounting width: this must match the tube or bracket.
- Bolt hole size: sets the bolt diameter through the joint.
- Weld-on or threaded: some adapters and joints must be welded.
- Serviceability: some joints grease through a fitting, and some can be rebuilt.
Safety and workmanship
Suspension links, cage components and steering parts are safety-critical. Welding should be done by someone qualified, using correct tube wall thickness, proper penetration and heat control. Use proper-grade hardware, tighten to specification, and fit jam nuts correctly with full thread engagement. Inspect joints regularly for play and cracks. For steering and suspension work you are unsure about, have a professional fabricator build and inspect it.
Think about the complete link before buying individual parts. A control arm or link is built from two ends, a tube and the hardware, and every piece must match: the thread of the ends has to match the tube adapter, and the bolt diameter must match the mounts on the axle and frame. Measure the center-to-center length you need with the suspension at ride height and again at full droop and full compression, so the ends never bind or run out of thread engagement.
The tools in this category make jobs safer and tidier. Joint presses and installation tools prevent damaged bushings, and a spindle nut socket or torsion key tool does a job that is awkward and risky with improvised tools. Brackets, gussets and tabs should be welded with clean, fully fused beads and placed to spread loads into the surrounding structure rather than concentrating stress on a single spot. Never grind or drill structural components without understanding how that changes their strength. Keep a record of the torque used on every fastener and recheck after the first trail outing.
Keep spare hardware on hand for trail repairs, including a few jam nuts, grade-rated bolts, nylon-insert locknuts and extra misalignment spacers, since these small parts are easy to lose and hard to improvise. Mark the final position of each adjustable end with paint so you can see at a glance if anything has turned. Store rod ends clean and lightly oiled, because rust inside a spherical bearing causes binding and premature wear.
Compatibility
Many items here are universal, so fitment depends on your design. Confirm dimensions and thread specifications from the manufacturer before choosing a product below.
Popular Fabrication & Tools brands
- Artec Industries (94)
- Rubicon Express (72)
- RockJock 4x4 (56)
- Currie (52)
- Trail Gear (44)
- TeraFlex (31)
- Fabtech (26)
- Blue Torch Fabworks (23)
- Rock Krawler (18)
- Mountain Off Road Enterprises (15)
- Poison Spyder Customs (13)
- Pro Comp Suspension (13)
Shop Fabrication & Tools by type
- Shock Mounts (72)
- Gussets & Tabs (59)
- Flex Joints, Rod Ends & Jam Nuts (116)
- Flex Joints (62)
- Tube Adapters (26)
- Brackets, Gussets & Tabs (80)
- Jam Nuts (17)
- Leaf Spring Perch (17)
- Tubing & Tube Adapters (12)
- Misalignment Spacers & Washers (9)
- Shock Absorber Wrench (8)
- Joint Tools (6)
- Roll Cage Gusset (7)
- Leaf Spring Accessories (3)
- Link Arm End (6)
- Nut-Sert Installation Tool (1)
- Sockets (3)
- Tool Bits (2)
- Specialty Tools (4)
- Drill Bits (0)
- Siphons (2)
- Hand Tools (2)
- Torsion Key Unloading Tool (2)
- Spindle Nut Socket (2)
- Oil Screen Installation Tool (0)
- Hose Cutter (1)
- Roll Cage Accessories (1)
- Knuckle Pull Scale (1)
- Garage Tools (1)
Fabrication & Tools FAQ
What is a Johnny Joint?
A Johnny Joint is a trademarked style of flex joint that places a bushing inside a threaded housing so a link or arm can pivot and twist. It is quieter than a heim joint and widely used in control arms and track bars.
What is the difference between a heim joint and a flex joint?
A heim joint uses a metal spherical bearing for precise, rigid movement, but it can be noisy and needs inspection. A flex joint uses a bushing, often urethane, which dampens noise and vibration while still letting the link articulate.
Why do rod ends come in left-hand and right-hand threads?
Pairing one left-hand and one right-hand end lets you turn a single link tube to lengthen or shorten it without removing either end. Jam nuts then lock the adjustment so the threads cannot back out.
Do I need to weld tube adapters?
Many tube adapters and weld-in joints must be welded to the tubing, while others thread in. Check the product description. Welding structural suspension parts should be done by a qualified fabricator using suitable tube material and technique.









