Select your vehicle

Advance Adapters GM SM420 Transmission To Dana 18/20 Transfer Case Adapter – 50-2400

Advance Adapters

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • GM SM420 transmission to Dana 18 or Dana 20 transfer case adapter
  • 4.50 inch long, 356-T6 aluminum alloy
  • Requires a retainer and sealed bearing, sold separately
  • Includes new transmission main shaft and mount block
  • Part number 50-2400

Description

Overview

It is a 4.50 inch adapter that connects a GM SM420 four-speed transmission to a Dana Spicer 18 or Dana 20 transfer case. It is made for the GM SM420 and includes a new output shaft.

The SM420 was used in GM trucks from 1947 to 1968. It has a 10-spline output shaft and was used in both two-wheel-drive and divorced four-wheel-drive applications, where the transfer case is mounted separately from the transmission. The adapter is made from 356-T6 heat-treated aluminum alloy and has a provision for a transmission mount.

It fits Dana Spicer 18 or 20 transfer cases of the Scout version, which have a 6-tooth female drive gear. The transfer case index must be matched to the new adapter, which requires an index retainer and a sealed bearing. The retainer depends on the transfer case bore: the 3-1/8 inch small hole or the 4 inch large hole.

Key features

  • Connects a GM SM420 four-speed to a Dana 18 or Dana 20 transfer case
  • Adapter length 4.50 inch
  • 356-T6 heat-treated aluminum alloy housing
  • Provision for a transmission mount
  • Includes a new transmission main shaft

Rebuilding a divorced transfer case

A divorced four-wheel-drive setup, where the transfer case sits behind a separate transmission, often means the transfer case has been around for decades. Before fitting a new adapter, inspect its output bearings, seals and shift linkage. Old bearings that feel rough or loose should be replaced while the case is open, because the adapter work is much harder to repeat later.

Shift linkage and input alignment are worth checking together. Look for wear at the shifter pivots and the linkage bushings, since a loose linkage makes an otherwise good adapter feel vague in use. Clean the mating faces thoroughly and use fresh gaskets, not the old ones.

  • Replace worn output bearings and seals while the case is open
  • Inspect shift linkage bushings and pivots
  • Clean mating faces and use fresh gaskets

Specifications

Brand Advance Adapters
Part number 50-2400
Adapter length 4.50 inch
Housing material 356-T6 heat-treated aluminum alloy
Transmission GM SM420 four-speed, 10-spline output shaft
Transfer case Dana Spicer 18 or 20, Scout version, 6-tooth female drive gear
Transfer case bore 3-1/8 inch small hole or 4 inch large hole
Index retainer options ADV716001 (large hole) or ADV716002 (small hole)
Sealed bearing ADV716302
GM SM420 use GM trucks, 1947 to 1968
Included Adapter housing, new transmission main shaft, mount block, gaskets, seal, nylon lock nut and instructions

Vehicle fitment

It is built for GM trucks from 1947 to 1968 that used the SM420. Check the transmission and transfer case rather than the vehicle model. Confirm fit for your vehicle’s year, model and trim before ordering.

Installation notes

Measure the transfer case bore first. A 3-1/8 inch small hole needs ADV716002 and a 4 inch large hole needs ADV716001. The index retainer and the ADV716302 sealed bearing are both required and are sold as options, not with the kit.

What’s included

The kit includes the adapter housing, a new transmission main shaft, a mount block, gaskets, a seal, a nylon lock nut and adapter instructions.

Not included: the index retainer (ADV716001 or ADV716002) and the sealed bearing (ADV716302), which are required options sold separately.

Questions & Answers

Which retainer do I need for the 50-2400?

It depends on the transfer case bore. Advance Adapters lists ADV716001 for the 4 inch large hole and ADV716002 for the 3-1/8 inch small hole. Measure the bore before ordering, because the wrong retainer will not index the case.

Does the 50-2400 fit the GM SM420 with a 10-spline output?

Yes. It is made for the GM SM420 four-speed, which has a 10-spline output shaft, and it includes a new transmission main shaft to match.

Is a sealed bearing included with the 50-2400?

No. The ADV716302 sealed bearing is a required option and must be ordered separately, along with the correct index retainer.

Can I reuse the old transfer case seals?

It is usually better to replace them. Seals harden with age and heat, and the adapter installation disturbs the mating faces, so new seals reduce the chance of leaks once the drivetrain is back in service.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon