Receiver Hitches
Showing 133–144 of 151 resultsSorted by popularity
-
Receiver Hitches
DrawTite Class III/IV Max-E-Loader Trailer Hitch – 41531
- Class III/IV rear receiver hitch with a 2 inch by 2 inch receiver opening
- Rated 3500 lbs GTW and 300 lbs tongue weight
- Fits selected 2004–2006 Jeep Wrangler LJ and 1997–2006 Jeep Wrangler TJ trims.
- Welded construction, black powder coat, no drilling required
- Part number 41531, UPC 742512415315
SKU: DRA41531 -
Receiver Hitches
DrawTite Class III/IV Max-E-Loader Trailer Hitch – 41015
- Fits 1991–1997 Toyota Land Cruiser (Base) and 1996–1997 Lexus LX450 (Base)
- Class III/IV Max-E-Loader receiver hitch, rear position, 2 inch receiver
- 5000 lbs. GTW and 6000 lb weight distribution
- 500 lb tongue weight and 750 lb weight distribution tongue weight
- Part number 41015
SKU: DRA41015 -
Receiver Hitches
DrawTite Class II Frame Trailer Hitch – 36408
- Fits 2005–2013 Chevrolet Equinox, 2010–2012 GMC Terrain, 2006–2009 Pontiac Torrent and 2002–2007 Saturn Vue in the listed trims
- Class II frame hitch, rear position, 1.25 inch receiver
- Rated 3500 lb GTW and 300 lb tongue weight
- Ball mount, pin and clip included
- Part number 36408; no drill required
SKU: DRA36408 -
Receiver Hitches
DrawTite Class III Max-Frame Receiver Hitch – 76104
- Fits 2007–2017 Jeep Wrangler (JK) in the listed trims
- Class III max-frame receiver hitch, rear position, 2 inch square receiver
- Rated up to 4,500 lbs. GTW for weight carrying and weight distributing
- A-Coat base with black powder coat finish
- Part number 76104; does not fit right hand drive vehicles
SKU: DRA76104 -
Receiver Hitches
DrawTite Class III/IV Round Tube Max-Frame Trailer Hitch – 75896
- Fits 2014 Toyota Highlander (Hybrid Limited, LE, LE Plus, Limited, XLE)
- Class III/IV round tube max-frame hitch, rear mount, part number 75896
- Rated 6000 lb gross trailer weight and 900 lb tongue weight
- Weight distribution ratings of 8000 lb GTW and 900 lb tongue weight
- All-welded construction with nationwide lifetime warranty
SKU: DRA75896 -
Receiver Hitches
DrawTite Class III/IV Round Tube Max-Frame Trailer Hitch – 75866
- Fits 2014 Chevrolet Silverado 1500 and 2014 GMC Sierra 1500 in the listed trims
- Class III/IV round tube max-frame hitch, rear position, 2 inch receiver
- 6000 lb gross trailer weight and 12000 lb weight distributing
- 900 lb tongue weight and 1200 lb weight distributing tongue weight
- Part number 75866
SKU: DRA75866 -
Receiver Hitches
DrawTite Class III/IV Round Tube Max-Frame Trailer Hitch – 75758
- Fits 2013 Ford Escape (S, SE, SEL, Titanium)
- Class III/IV round tube max-frame hitch, rear position, part number 75758
- 3500 lb GTW and 525 lb tongue weight; 4000 lb weight distribution GTW
- 2 inch receiver; no drill required; 15 minute install time
- Does not fit with a roll pan
SKU: DRA75758 -
Receiver Hitches
DrawTite Class V Ultra Frame Hitch – 41943
- Fits 1999–2005 and 2007–2012 Ford F-350 Super Duty (King Ranch, Lariat, XL, XLT)
- Class V Ultra Frame receiver hitch, rear position, part number 41943
- Rated 16000 lb GTW and 2400 lb tongue weight
- All-welded construction, built to fit the specific vehicle with no adapters
- Drilling required; install time 40 minutes
SKU: DRA41943 -
-
Receiver Hitches
Crown Automotive Trailer Hitch with Hardware – 52060290K
- Fits 2007–2018 Jeep Wrangler (JK) in the listed trims
- 2 inch receiver, rear position, Class II weight class
- 3500 lb towing capacity and 350 lb tongue weight
- No drilling required; grade 8 bolts and washers included
- Part number 52060290K
SKU: CRO52060290K -
Receiver Hitches
B&W Trailer Hitches Class 5 Heavyduty Receiver Hitch (Black) – HDRH25230
- Class 5 rear receiver hitch with a 2 Inches X 2 Inches receiver tube
- Rated for a 16,000 lbs weight capacity and 1600 lbs tongue weight
- Named for 99-10 Ford F250/F350 and 08-10 Ford F450 trucks with factory bumpers
- Three-piece interlocking design on a six point frame mount
- Includes trailer plug bracket and Grade 8 mounting hardware
- Part number HDRH25230, UPC 843233000856
SKU: BNWHDRH25230
Understanding hitch classes
Hitches are grouped by class according to their rated gross trailer weight and tongue weight. Class III hitches are common on SUVs, half-ton trucks and Jeeps, while Class IV and V hitches are built for heavier trailers and larger trucks. Receivers are normally 1.25 inch or 2 inch square, and Class III and above generally use 2 inch. A higher class does not raise your vehicle's tow rating, because the lowest-rated component in the whole system sets the limit.
Specifications to check
- Gross trailer weight (GTW): The maximum total trailer weight the hitch is rated for.
- Tongue weight (TW): The downward force on the ball, typically around 10 to 15 percent of trailer weight for conventional trailers.
- Receiver size: Confirm it matches your ball mount, bike rack or accessory shank.
- Weight-distributing rating: Some hitches carry different ratings with and without a weight-distribution system.
- Mount location: Rear hitches are standard, while front receivers are sold as separate designs.
Fitment and compatibility
Direct-fit hitches are made for a particular chassis, with bolt holes that line up with factory frame points. Bumper cutouts, exhaust routing, spare tire carriers and roll pans can interfere, and some listings note whether the hitch fits with a roll pan. Always confirm fitment for your exact year, make and model, and check the manufacturer's specifications and your owner's manual for the vehicle's tow rating.
Installation notes
Most bolt-on hitches install with basic hand tools and a helper, but they carry a lot of load, so fastener quality and torque matter. Use the supplied hardware, tighten to the specified torque, and recheck after the first drive. Clean and treat any weld seams or drilled areas against rust. Wiring for trailer lights is a separate harness. If you are unsure about any step, have the hitch installed by a professional, and inspect it periodically for cracks, loose bolts and corrosion.
Check the fine print when you pair a hitch with accessories. A ball mount, pin, coupler and chains each carry their own rating, and the lowest rating in the chain is your limit. Keep the receiver tube clean and lightly lubricated, and use an anti-rattle device if your accessories shift in the opening.
Wiring, ball mounts and common pairings
A hitch is only part of a towing setup. You will also need a ball mount with the right rise or drop so the trailer sits level, a ball sized to the trailer coupler, and a hitch pin or locking pin. Safety chains cross under the tongue, and trailers over a certain weight need brakes and a brake controller, with requirements that vary by state.
- Choose a ball mount length that gives clearance between the trailer and the vehicle at tight turns.
- Use a wiring harness that matches your vehicle's connector, and test the lights before every trip.
- Grease the ball lightly and keep the coupler latch free of dirt.
Look over the receiver for rust and bent tubing after trail use, and replace any hitch that shows cracks or elongated bolt holes.
Popular Receiver Hitches brands
- Curt Manufacturing (67)
- DrawTite (47)
- B&W Hitch (16)
- Rugged Ridge (7)
- Smittybilt (4)
- Warn (3)
- Fab Fours (2)
- Trimax Locks (2)
- Rampage (1)
- Genuine Packages (1)
- RT Off-Road (1)
- Ranch Hand (1)
Receiver Hitches FAQ
What hitch class do I need?
Match the class to the trailer you plan to tow, then confirm it does not exceed your vehicle's rated towing capacity. Class III suits many SUVs and Jeeps, while heavier trailers call for a higher class on a capable vehicle.
Does a Class V hitch increase my towing capacity?
No. Towing capacity is set by the vehicle manufacturer and by the weakest component, including the frame, axle, brakes and hitch. A stronger hitch alone does not raise the vehicle's limit.
What is tongue weight?
Tongue weight is the downward force the trailer places on the hitch ball. For many conventional trailers it should fall near 10 to 15 percent of trailer weight, and it must stay within the hitch's rating.
Can I install a receiver hitch myself?
Many direct-fit hitches bolt to existing frame holes and can be installed at home with a helper and a torque wrench. If drilling, welding or trimming is involved, a professional installer is recommended.











