Receiver Hitches
Showing 145–151 of 151 resultsSorted by popularity
-
-
-
Receiver Hitches
Patriot Hitch Package – HITPAKMK2
- Genuine Packages Patriot Hitch Package, part number HITPAKMK2
- 2 inch square receiver tube, rear position, Class III/IV weight class
- Rated 4000 lb gross trailer weight and 400 lb tongue weight
- Gloss black powder coat finish; 30 minute install with no drilling
- All installation hardware included; no vehicle fitment listed
SKU: ADDHITPAKMK2 -
Receiver Hitches
DrawTite Class III/IV Max-Frame Trailer Hitch – 75662
- DrawTite Class III/IV Max-Frame rear trailer hitch, part number 75662
- 2 in. receiver with 6000lbs. GTW carrying rating
- 10000lbs. GTW with weight distributing
- Designed for models without a factory-installed receiver
- UPC 742512756623
SKU: DRA75662 -
Receiver Hitches
DrawTite Class III/IV Max-Frame Trailer Hitch – 75699
- DrawTite Class III/IV Max-Frame rear trailer hitch, part number 75699
- 2-inch square receiver opening, all welded
- Rated up to 5,000 lbs. GTW for weight carrying
- Rated up to 7,500 lbs. GTW for weight distributing
- Attaches at all frame attachment points, UPC 742512756999
SKU: DRA75699 -
Receiver Hitches
Smittybilt Hitch Kit – JH45K
- Gloss black powder coated receiver hitch for towing
- 2-door models rated for 2500 lb gross trailer weight and 250 lb tongue weight
- 4-door models rated for 3500 lb gross trailer weight and 350 lb tongue weight
- Plug and play wiring adaptor for the OEM harness, with no cutting or splicing
SKU: S/BJH45K
Understanding hitch classes
Hitches are grouped by class according to their rated gross trailer weight and tongue weight. Class III hitches are common on SUVs, half-ton trucks and Jeeps, while Class IV and V hitches are built for heavier trailers and larger trucks. Receivers are normally 1.25 inch or 2 inch square, and Class III and above generally use 2 inch. A higher class does not raise your vehicle's tow rating, because the lowest-rated component in the whole system sets the limit.
Specifications to check
- Gross trailer weight (GTW): The maximum total trailer weight the hitch is rated for.
- Tongue weight (TW): The downward force on the ball, typically around 10 to 15 percent of trailer weight for conventional trailers.
- Receiver size: Confirm it matches your ball mount, bike rack or accessory shank.
- Weight-distributing rating: Some hitches carry different ratings with and without a weight-distribution system.
- Mount location: Rear hitches are standard, while front receivers are sold as separate designs.
Fitment and compatibility
Direct-fit hitches are made for a particular chassis, with bolt holes that line up with factory frame points. Bumper cutouts, exhaust routing, spare tire carriers and roll pans can interfere, and some listings note whether the hitch fits with a roll pan. Always confirm fitment for your exact year, make and model, and check the manufacturer's specifications and your owner's manual for the vehicle's tow rating.
Installation notes
Most bolt-on hitches install with basic hand tools and a helper, but they carry a lot of load, so fastener quality and torque matter. Use the supplied hardware, tighten to the specified torque, and recheck after the first drive. Clean and treat any weld seams or drilled areas against rust. Wiring for trailer lights is a separate harness. If you are unsure about any step, have the hitch installed by a professional, and inspect it periodically for cracks, loose bolts and corrosion.
Check the fine print when you pair a hitch with accessories. A ball mount, pin, coupler and chains each carry their own rating, and the lowest rating in the chain is your limit. Keep the receiver tube clean and lightly lubricated, and use an anti-rattle device if your accessories shift in the opening.
Wiring, ball mounts and common pairings
A hitch is only part of a towing setup. You will also need a ball mount with the right rise or drop so the trailer sits level, a ball sized to the trailer coupler, and a hitch pin or locking pin. Safety chains cross under the tongue, and trailers over a certain weight need brakes and a brake controller, with requirements that vary by state.
- Choose a ball mount length that gives clearance between the trailer and the vehicle at tight turns.
- Use a wiring harness that matches your vehicle's connector, and test the lights before every trip.
- Grease the ball lightly and keep the coupler latch free of dirt.
Look over the receiver for rust and bent tubing after trail use, and replace any hitch that shows cracks or elongated bolt holes.
Popular Receiver Hitches brands
- Curt Manufacturing (67)
- DrawTite (47)
- B&W Hitch (16)
- Rugged Ridge (7)
- Smittybilt (4)
- Warn (3)
- Fab Fours (2)
- Trimax Locks (2)
- Genuine Packages (1)
- RT Off-Road (1)
- Ranch Hand (1)
- Street Scene (1)
Receiver Hitches FAQ
What hitch class do I need?
Match the class to the trailer you plan to tow, then confirm it does not exceed your vehicle's rated towing capacity. Class III suits many SUVs and Jeeps, while heavier trailers call for a higher class on a capable vehicle.
Does a Class V hitch increase my towing capacity?
No. Towing capacity is set by the vehicle manufacturer and by the weakest component, including the frame, axle, brakes and hitch. A stronger hitch alone does not raise the vehicle's limit.
What is tongue weight?
Tongue weight is the downward force the trailer places on the hitch ball. For many conventional trailers it should fall near 10 to 15 percent of trailer weight, and it must stay within the hitch's rating.
Can I install a receiver hitch myself?
Many direct-fit hitches bolt to existing frame holes and can be installed at home with a helper and a torque wrench. If drilling, welding or trimming is involved, a professional installer is recommended.




