Select your vehicle

Showing 61–72 of 86 resultsSorted by popularity

What goes in this category

The ball mount is the removable piece that slides into the receiver tube and carries the ball. A drop hitch lowers the ball, a rise hitch lifts it, and both let the trailer sit level. Related items in this category include the hitch ball itself, the pin that locks the mount in the receiver, locking pins for the coupler, and bushings that reduce rattle.

How to choose a ball mount

Start with the receiver size. Common shank sizes are 1-1/4 inch for light-duty classes and 2 inch for heavier classes, and the mount must match your receiver. Then measure the ride height: with the trailer level, measure from the ground to the top of the receiver opening and from the ground to the bottom of the coupler. The difference tells you how much drop or rise you need.

  • Fixed mounts: Simple and strong for a single trailer.
  • Adjustable mounts: Useful if you tow different trailers or have a height-varying setup.
  • Multi-ball mounts: Hold more than one ball size for different couplers.

Ratings and sizes

Every part in the towing chain has a rating, and the lowest one governs. Check the mount's gross trailer weight and tongue weight ratings and compare them to your trailer, your receiver class and the tow rating in your owner's manual. Hitch balls come in different diameters, such as 1-7/8, 2 and 2-5/16 inches, and the ball must match the coupler stamped size. The shank diameter has to fit the hole in the mount, and the ball needs the proper nut and washer torque.

Safety and installation notes

Use a mount rated at or above your loaded trailer's weight. A level trailer tows more stably and puts the weight where it should be. A coupler that rides nose-high or nose-low can affect braking and sway. Torque the ball nut to the manufacturer's specification and check it regularly, and always install the hitch pin and a clip or lock.

Confirm that the mount fits your receiver and vehicle, and check that your vehicle's tow rating and hitch class support the load. If you are unsure about weight distribution or trailer sway control, a professional hitch shop can help. Never exceed the lowest rated component in the setup, and verify ratings in the manufacturer's specifications.

Maintenance and common mistakes

Inspect the ball and mount before each season. Look for cracks in the shank, bent platforms, deep rust, and wear on the ball surface, which should be smooth and round. A ball that is flattened or pitted can cause coupler wear and should be replaced. Keep the ball lightly greased unless your coupler instructions say otherwise, and wipe it clean after each trip.

Rattle in the receiver is common and mostly cosmetic, but it can wear the receiver tube over time. Anti-rattle devices and bushings address this, and they are separate from the load-carrying parts. The hitch pin should be the correct diameter for the receiver, such as 5/8 inch for many class III and IV receivers, and a lock helps deter theft.

Common mistakes include using a mount rated for a lighter class, forgetting the clip on the pin, overtightening the ball nut past its torque, and ignoring tongue weight. As a general guideline, tongue weight is often around 10 to 15 percent of trailer weight for conventional trailers, but follow the trailer maker's recommendation. Store the mount in a dry place when it is not being used.

Popular Drop Hitches & Ball Mounts brands

Shop Drop Hitches & Ball Mounts by type

Drop Hitches & Ball Mounts FAQ

How do I know how much drop I need?

Park on level ground with the trailer level. Measure from the ground to the top of the receiver opening and from the ground to the coupler's bottom. The difference is the drop or rise you need.

What do the hitch classes mean?

Classes group receivers by capacity and size, from Class I for light loads up to Class V for heavy trailers. Class III and IV commonly use 2 inch receivers. Your vehicle's tow rating and the lowest rated part still apply.

How do I choose the right ball size?

Read the size stamped on the trailer coupler, commonly 1-7/8, 2 or 2-5/16 inches. The ball must match that size, fit the mount's hole diameter, and be rated for the trailer's weight.

Is an adjustable ball mount a good idea?

It can be, especially if you tow multiple trailers. It has more moving parts, so check that the rating matches your load and that all locking hardware is secure and torqued before each trip.