Select your vehicle
-13%

TeraFlex Falcon SP2 3.5 aDAPT e-Adjust Piggyback Shock Set for 2 -4.5″ Lift – 11-04-35-400-200

TeraFlex

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Falcon SP2 3.5 aDAPT e-Adjust piggyback shock set for 2 to 4.5 inch lift
  • Automatic switch from Soft to a preselected Firm setting
  • Three-position in-cab switch with Soft, Firm and Auto
  • Eight-position dial for manual Firm tuning
  • Part number TER11-04-35-400-200

Description

Overview

The TeraFlex Falcon SP2 3.5 aDAPT e-Adjust piggyback shock set, part number TER11-04-35-400-200, is a front and rear hydraulic piggyback set for 2018–2026 Jeep Wrangler (JL) Unlimited four-door models with a 2 to 4.5 inch lift. The top and bottom mounts are OEM.

The aDAPT system switches the shocks from Soft to a manually preselected Firm setting depending on terrain. The aDAPT control module has a three-position in-cab switch with Soft, Firm and Auto settings, and the Firm setting is tuned with the eight-position dial. The shocks are built for both daily driving and off-road use. The kit uses the factory mounting points, and the aDAPT module can be programmed to switch automatically between Soft and a preselected Firm setting.

Key features

  • Automatic switch from Soft to a preselected Firm setting
  • Three-position in-cab switch: Soft, Firm and Auto
  • Eight-position dial for the manual Firm setting
  • Piggyback reservoir design, front and rear
  • OEM top and bottom mounts
  • Hydraulic operation

Automatic versus manual firm

Auto mode is useful when terrain changes often, because the module can move from Soft to Firm without a manual change at the switch. A driver still decides the preselected Firm level, so the setup reflects their own driving. On mostly paved roads, keeping the switch on Soft may feel more comfortable, and the Firm setting can then be reserved for trail sections.

Piggyback shocks depend on the module, wiring and in-cab switch working together, so any fault in those parts can leave the shocks in the wrong setting. Check the switch cycles through all three positions after installation. Keep the bump stop clearance in mind, since the shocks reach full compression on rough ground.

  • Confirm the in-cab switch cycles through all positions
  • Check bump stop clearance at full compression
  • Recheck mounts after the first few drives

Specifications

Brand TeraFlex
Part number TER11-04-35-400-200
Product line Falcon SP2 3.5 aDAPT e-Adjust
Shock type Piggyback
Location Front and rear
Lift height 2-4.5 in.
Top mount OEM
Bottom mount OEM
Controls In-cab 3-position switch; 8-position dial
Operation Hydraulic
Fitment Direct fit

Vehicle fitment

It fits the 2018–2026 Jeep Wrangler (JL) Unlimited four-door models in the Moab, Rubicon, Sahara, Sport and Sport S versions. It is sized for a 2 to 4.5 inch lift.

The list covers the four-door JL Unlimited only, so two-door Wranglers and the JK and Gladiator models are not included. Confirm your vehicle’s year, model and trim before ordering.

Installation notes

Bump stop configuration depends on the shock’s collapsed length, tire size and fenders, so follow the instructions for your application. The 2 inch bump stop strike pad extension kit, part number 1959500, and or 0.5 inch bump stop strike pad shim kits, part number 1959300, may be needed.

What’s included

One front and rear set of Falcon SP2 3.5 aDAPT e-Adjust piggyback shocks, part number TER11-04-35-400-200, with the aDAPT control module and in-cab switch.

Fitment

VehicleYearsTrims
Jeep Wrangler (JL)2018–2026Unlimited Moab (4-Door), Unlimited Rubicon (4-Door), Unlimited Sahara (4-Door), Unlimited Sport (4-Door), Unlimited Sport S (4-Door)

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Will the TeraFlex TER11-04-35-400-200 fit a 2023 Jeep Wrangler JL?

No. The fitment for this set covers the 2018 to 2026 Jeep Wrangler JL Unlimited four-door models only. Confirm your vehicle's year, model and trim before ordering.

What does the Auto setting do?

In Auto, the aDAPT control module switches the shocks from Soft to the Firm setting you preselected, based on terrain. The in-cab switch selects Soft, Firm or Auto.

Does it need a bump stop kit?

It may. The bump stop configuration depends on the collapsed length, tire size and fenders. The 2 inch bump stop extension kit, part number 1959500, or the 0.5 inch shim kits, part number 1959300, may be required.

What lift range does it cover?

It covers a 2 to 4.5 inch lift on the four-door Wrangler JL Unlimited. The top and bottom mounts are OEM, so the factory mounting points are used.

Should the switch stay in Auto all the time?

Auto suits drivers who change terrain often, since it moves to Firm without a manual change. On mostly paved roads, Soft may feel more comfortable. Choose the mode that fits your usual driving and check the switch position before a trail section.

What should be checked after installing piggyback shocks?

Check bump stop clearance at full compression, confirm the reservoir hoses have room to move, and make sure the in-cab switch cycles through all three settings. Recheck the mounts after the first few drives.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon