Carburetors, Intake Manifolds, and Throttle Body brings together the fuel and air parts for carbureted and early fuel injected Jeeps and trucks: Weber and Holley carburetors, Carter and Quadrajet rebuild kits and jets from Jet Performance Products, mechanical fuel pumps and throttle cables from Omix-Ada and Crown Automotive, and carburetor adapters and spacers from Mr. Gasket Company, with Edelbrock parts alongside.Identify your carburetor and engine first, then compare the products below.
Carburetors, Intake Manifolds, and Throttle Body
Showing 1–12 of 40 resultsSorted by popularity
Shop Carburetors, Intake Manifolds, and Throttle Body by type
-
Accelerator Cable
Omix-ADA Throttle Control Cable – 17716.16
- Omix-ADA throttle control cable, part number 17716.16
- Fits 1991–2001 Jeep Cherokee (XJ), 1991–1992 Comanche and 1993–1996 Grand Cherokee (ZJ)
- Direct OE replacement for a worn or lengthened throttle control cable
- Made to original specifications.
SKU: OAI17716.16 -
-
Electric Fuel Pump
Omix-ADA Fuel Pump (Natural) – 17709.06
- Omix-ADA natural fuel pump, part number OAI17709.06
- Fits 1974–1983 CJ5, 1974–1975 CJ6, 1976–1986 CJ7, 1981–1985 Scrambler and 1987–1990 Wrangler YJ
- Designed for 232 and 258 six cylinder engines
- New pump, not remanufactured, with mounting gasket included
SKU: OAI17709.06 -
-
Carburetor Adapter
Mr. Gasket Company Carburetor Adapter Kit 9/16 in. – 1937
- Mr. Gasket Company carburetor adapter kit, 9/16 in., part number MRG1937
- Adapts from a 2 bbl carburetor to a 2 bbl intake
- Gaskets, studs, nuts and washers included
- Universal fit for 2 bbl carburetor and intake setups
SKU: MRG1937 -
Carburetor Adapter
Mr. Gasket Company Carburetor Adapter Kit 0.75 Inch – 1932
- Mr. Gasket Company carburetor adapter kit, 0.75 inch, part number MRG1932
- Square-bore to square-bore adapter, die cast aluminum
- Gaskets, studs, nuts and washers included
- Universal fit; match bore and mounting first
SKU: MRG1932 -
-
-
-
Repair, replace or upgrade
A carbureted Jeep or truck that starts hard, stumbles off idle or floods usually has a tired carburetor, a weak fuel pump or a worn throttle linkage, and this category covers all three. Rebuild kits with gaskets, needle and seat, accelerator pump and float adjustments restore an original Carter, Rochester Quadrajet or Motorcraft unit. A replacement carburetor, such as the Weber conversions sold for 1977 to 1990 CJs, Wagoneers, J10s and YJs, swaps a troublesome emissions-era carburetor for a simpler one. Street performance carburetors like the Holley Street Avenger step up airflow for a V8 truck. Decide which of these you are doing before buying parts, since a jet kit for a Quadrajet is useless on a Weber.
Identifying what you have
Carburetors are identified by the maker and a tag or stamped number, not the vehicle. A Carter kit here lists tag number 637S; Quadrajet parts are sold for the 4M series by jet size. Find the number on the airhorn or a tag under a bowl screw before ordering a kit. For fuel pumps, the engine matters: the 232 and 258 sixes, the 225 Buick V6 and the early flathead and F-head fours use different pumps, and a diaphragm pump for a 225 will not bolt to a 258. Throttle cables are sold by year range and body, for example 1991 to 2001 XJ and 1993 to 1996 ZJ, so confirm your years rather than comparing lengths by eye.
Carburetor adapters and spacers
- Adapters let a carburetor with one base pattern sit on an intake with another, for example two-barrel to two-barrel with different bolt spacing or square bore to square bore with an offset. Match both the carburetor flange and the manifold flange exactly.
- Spacers add plenum volume and distance between the throttle plates and the manifold floor, which can smooth idle and help mid-range on some engines. Open spacers favor top end, four-hole spacers favor low speed response.
- Every spacer or adapter raises the carburetor, so check hood and air cleaner clearance and whether the throttle and choke linkage still reach.
- Use new gaskets on both faces and torque evenly to avoid warping a thin aluminum adapter.
Choosing a performance carburetor
Carburetor size is rated in cubic feet per minute. A 570 cfm four-barrel suits a mild small block in a truck; bigger is not better, because an oversized carburetor hurts low speed response and fuel economy where a truck lives. Vacuum secondaries open based on engine demand and are the forgiving choice for a heavy vehicle, while mechanical secondaries belong on lighter, higher revving builds. An electric choke simplifies cold starts compared with a manual cable. Confirm the base pattern and fuel inlet orientation against your manifold and fuel line.
Installation and tuning
Replace the fuel filter and inspect rubber fuel lines for cracking when you change any fuel part; old lines fail when ethanol fuel meets a disturbed hose. Set float level per the kit instructions, adjust idle mixture screws with a vacuum gauge or by ear for the highest steady idle, then set idle speed. On a Weber conversion, the electric choke needs a switched 12 volt source. Check for vacuum leaks at the base gasket with a spray of carburetor cleaner around the flange; a change in idle speed means a leak. Mechanical fuel pumps should deliver 4 to 7 psi on most of these engines, and a pressure above that overwhelms the needle and seat and floods the engine.
Work with the battery disconnected when removing fuel parts, keep a fire extinguisher nearby, and let the engine cool before touching the fuel system.
Popular Carburetors, Intake Manifolds, and Throttle Body brands
- Crown Automotive (18)
- Omix-Ada (12)
- Edelbrock (4)
- Holley Performance (3)
- Jet Performance Products (3)
- Mr. Gasket Company (3)
Carburetors, Intake Manifolds, and Throttle Body FAQ
How do I identify my carburetor for a rebuild kit?
Look for a stamped number on the airhorn or a metal tag under one of the bowl screws. Carter, Rochester Quadrajet, Holley and Motorcraft each have their own numbering, and kits are matched to that number rather than to the vehicle. Photograph it before ordering parts.
Is a Weber carburetor a good replacement on a Jeep CJ?
Many owners replace the original emissions-era carburetor on 1977 to 1990 CJs, Wagoneers, J10s and YJs with a Weber for simpler adjustment and reliable cold starting with an electric choke. It is a direct fit with the included adapter and needs a switched 12 volt feed for the choke.
What fuel pressure does a carbureted engine need?
Most of the engines here run well on 4 to 7 psi from a mechanical pump. Higher pressure pushes fuel past the needle and seat and floods the carburetor. If you fit an electric pump, use a regulator and a return line or a pressure rated for carburetors.
Does a carburetor spacer add power?
On some engines a spacer smooths idle and helps mid-range torque by adding plenum volume, and a four-hole spacer sharpens low speed response. Gains are modest. Check hood clearance and linkage reach, since a spacer raises the carburetor and air cleaner.






















