Carburetors, Intake Manifolds, and Throttle Body
Showing 13–24 of 40 resultsSorted by popularity
-
Carburetor Secondary Throttle Diaphragm
Holley Performance Secondary Diaphragm Spring Kit – HOL20-13
Carburetor Secondary Throttle DiaphragmHolley Performance Secondary Diaphragm Spring Kit – HOL20-13
- Holley Performance secondary diaphragm spring kit, part number HOL20-13
- Universal fit, not tied to a vehicle
- Description covers a hydraulic motor and planetary geartrain, so confirm contents
SKU: HOL20-13 -
Carburetor Idle Stop Solenoid
Crown Automotive Throttle Solenoid – 83502116
- Fits 1985–1993 Jeep Cherokee XJ, 1985–1986 CJ7, 1986–1990 Comanche, 1985 Scrambler and 1987–1990 Wrangler YJ
- Crown Automotive throttle solenoid, part number CRO83502116
- Made for a 4 cylinder engine and a direct fit
SKU: CRO83502116 -
EGR Valve
Crown Automotive EGR Valve Thermal Vacuum Switch – J3237457
- Crown Automotive EGR valve thermal vacuum switch, part number CROJ3237457
- For 2.5L, 2.8L and 4.2L four and six cylinder carbureted engines
- Ported vacuum switch
- Fits 1981–1986 Jeep Cherokee, CJ, Comanche, Grand Wagoneer, J10, Scrambler and Wagoneer models
SKU: CROJ3237457 -
Accelerator Cable
Omix-ADA Accelerator Cable – 17716.09
- Fits 1987–1990 Jeep Cherokee (XJ) in Base, Chief, Laredo, Limited, Pioneer and Sport trims
- Omix-ADA accelerator cable, part number 17716.09
- Designed for the 4.0L 6 cylinder engine
- Direct replacement built to original specifications, with a limited five year warranty
SKU: OAI17716.09 -
-
Carburetor Repair Kit
Omix-ADA Carburetor Repair Kit – 17705.06
- Omix-Ada carburetor repair kit, part number 17705.06
- For Carter one-barrel carburetors on 134 F-head engines
- Listed to include all parts needed for a carburetor rebuild
- Fits 1953-1971 Jeep Willys, CJ, DJ, J-series and related models
SKU: OAI17705.06 -
Repair, replace or upgrade
A carbureted Jeep or truck that starts hard, stumbles off idle or floods usually has a tired carburetor, a weak fuel pump or a worn throttle linkage, and this category covers all three. Rebuild kits with gaskets, needle and seat, accelerator pump and float adjustments restore an original Carter, Rochester Quadrajet or Motorcraft unit. A replacement carburetor, such as the Weber conversions sold for 1977 to 1990 CJs, Wagoneers, J10s and YJs, swaps a troublesome emissions-era carburetor for a simpler one. Street performance carburetors like the Holley Street Avenger step up airflow for a V8 truck. Decide which of these you are doing before buying parts, since a jet kit for a Quadrajet is useless on a Weber.
Identifying what you have
Carburetors are identified by the maker and a tag or stamped number, not the vehicle. A Carter kit here lists tag number 637S; Quadrajet parts are sold for the 4M series by jet size. Find the number on the airhorn or a tag under a bowl screw before ordering a kit. For fuel pumps, the engine matters: the 232 and 258 sixes, the 225 Buick V6 and the early flathead and F-head fours use different pumps, and a diaphragm pump for a 225 will not bolt to a 258. Throttle cables are sold by year range and body, for example 1991 to 2001 XJ and 1993 to 1996 ZJ, so confirm your years rather than comparing lengths by eye.
Carburetor adapters and spacers
- Adapters let a carburetor with one base pattern sit on an intake with another, for example two-barrel to two-barrel with different bolt spacing or square bore to square bore with an offset. Match both the carburetor flange and the manifold flange exactly.
- Spacers add plenum volume and distance between the throttle plates and the manifold floor, which can smooth idle and help mid-range on some engines. Open spacers favor top end, four-hole spacers favor low speed response.
- Every spacer or adapter raises the carburetor, so check hood and air cleaner clearance and whether the throttle and choke linkage still reach.
- Use new gaskets on both faces and torque evenly to avoid warping a thin aluminum adapter.
Choosing a performance carburetor
Carburetor size is rated in cubic feet per minute. A 570 cfm four-barrel suits a mild small block in a truck; bigger is not better, because an oversized carburetor hurts low speed response and fuel economy where a truck lives. Vacuum secondaries open based on engine demand and are the forgiving choice for a heavy vehicle, while mechanical secondaries belong on lighter, higher revving builds. An electric choke simplifies cold starts compared with a manual cable. Confirm the base pattern and fuel inlet orientation against your manifold and fuel line.
Installation and tuning
Replace the fuel filter and inspect rubber fuel lines for cracking when you change any fuel part; old lines fail when ethanol fuel meets a disturbed hose. Set float level per the kit instructions, adjust idle mixture screws with a vacuum gauge or by ear for the highest steady idle, then set idle speed. On a Weber conversion, the electric choke needs a switched 12 volt source. Check for vacuum leaks at the base gasket with a spray of carburetor cleaner around the flange; a change in idle speed means a leak. Mechanical fuel pumps should deliver 4 to 7 psi on most of these engines, and a pressure above that overwhelms the needle and seat and floods the engine.
Work with the battery disconnected when removing fuel parts, keep a fire extinguisher nearby, and let the engine cool before touching the fuel system.
Popular Carburetors, Intake Manifolds, and Throttle Body brands
- Crown Automotive (18)
- Omix-Ada (12)
- Edelbrock (4)
- Holley Performance (3)
- Jet Performance Products (3)
- Mr. Gasket Company (3)
Shop Carburetors, Intake Manifolds, and Throttle Body by type
- Accelerator Cable (15)
- Carburetors (6)
- Carburetor Repair Kit (5)
- Electric Fuel Pump (3)
- Carburetor Adapter (3)
- Carburetor Kit (2)
- Carburetor Spacer (2)
- Carburetor Jet (1)
- Carburetor Secondary Throttle Diaphragm (1)
- Carburetor Idle Stop Solenoid (1)
- EGR Valve (1)
Carburetors, Intake Manifolds, and Throttle Body FAQ
How do I identify my carburetor for a rebuild kit?
Look for a stamped number on the airhorn or a metal tag under one of the bowl screws. Carter, Rochester Quadrajet, Holley and Motorcraft each have their own numbering, and kits are matched to that number rather than to the vehicle. Photograph it before ordering parts.
Is a Weber carburetor a good replacement on a Jeep CJ?
Many owners replace the original emissions-era carburetor on 1977 to 1990 CJs, Wagoneers, J10s and YJs with a Weber for simpler adjustment and reliable cold starting with an electric choke. It is a direct fit with the included adapter and needs a switched 12 volt feed for the choke.
What fuel pressure does a carbureted engine need?
Most of the engines here run well on 4 to 7 psi from a mechanical pump. Higher pressure pushes fuel past the needle and seat and floods the carburetor. If you fit an electric pump, use a regulator and a return line or a pressure rated for carburetors.
Does a carburetor spacer add power?
On some engines a spacer smooths idle and helps mid-range torque by adding plenum volume, and a four-hole spacer sharpens low speed response. Gains are modest. Check hood clearance and linkage reach, since a spacer raises the carburetor and air cleaner.










