Roof and Windshield Lighting Mounts
Showing 13–24 of 24 resultsSorted by popularity
-
-
Roof and Windshield Lighting Mounts
Go Rhino Hard Top Rear Rear Light Mount Kit (Black) – 599501T
- Rear-facing light mount kit for a single 3 x 3 inch cube, dual cube or LED bar
- Fits 2018 Jeep Wrangler JL and JLU hard tops
- Mild steel with black powder coat finish
- No drilling, with rubber gasket and grommets
SKU: ORP599501T -
-
-
Roof and Windshield Lighting Mounts
DV8 Offroad Over Windshield Light Bar Bracket (Black) – LBJL-01
- Over windshield light bar bracket for a standard 50 inch LED light bar
- Installs with factory hardware, no drilling
- Textured black powder coat finish
- Fits 2018–2019 Wrangler JL and 2020–2026 Gladiator
SKU: DV8LBJL-01 -
Roof and Windshield Lighting Mounts
DeeZee Single Cowl Light Bracket – DZ4452JL
- Single cowl light bracket for the 2018–2026 Jeep Wrangler (JL) in the manufacturer fitment list
- Holds one cube light of your choice
- Heavy duty steel with textured black finish
- Installation hardware included, no drilling required
SKU: DEEDZ4452JL -
Roof and Windshield Lighting Mounts
DeeZee A-Pillar Accessory Bracket – DZ4451JL
- Dee-Zee A-pillar accessory bracket pair for cube lights
- Heavy duty steel with texture black powder coat
- Requires a hex series A-pillar; no drilling, hardware included
- Fits 2018-2026 Jeep Wrangler JL and 2020-2026 Gladiator
SKU: DEEDZ4451JL -
-
Roof and Windshield Lighting Mounts
Westin Pillar LED Light Mount – 09-41035
- Fits 2007–2016 Jeep Wrangler JK models, including Unlimited
- Mounts a 50 inch LED light bar to the pillars using existing OE bolt points
- 7 gauge mild steel in textured black, with stainless steel fasteners
- Foam gaskets included; sold as a set of 2; 3 year warranty
SKU: WES09-41035 -
Roof and Windshield Lighting Mounts
PIAA Jeep Wrangler TJ 97-06 Pillar Mount Bracket Kit (Black) – 30100
Roof and Windshield Lighting MountsPIAA Jeep Wrangler TJ 97-06 Pillar Mount Bracket Kit (Black) – 30100
- Pillar mount bracket kit made for the Jeep Wrangler TJ, 1997 to 2006
- Mounts to the existing windshield hinge bracket
- No drilling or cutting needed for installation
- Black powder coat finish
SKU: PIA30100 -
Roof and Windshield Lighting Mounts
N-FAB 49-Series Windshield Mount for LED Bar (Black ) – J9749WSM
Roof and Windshield Lighting MountsN-FAB 49-Series Windshield Mount for LED Bar (Black ) – J9749WSM
- Windshield mount for LED light bars, made for Jeep JK and TJ Wrangler models
- Holds one to three 50-inch LED light bars on one base bracket system
- Bolt-on design uses pre-existing factory holes in the windshield pillars
- Black finish, windshield hinge mounting type
SKU: N/FJ9749WSM -
Roof and Windshield Lighting Mounts
Carr Deluxe Rotabar Light Bar – 210871
- Fits many Chevrolet, GMC, Dodge, Ford, Jeep, Nissan and Toyota trucks and SUVs, model years 2004 to 2018
- Rotabar design rotates down for extra clearance or to protect the lights
- Black powdercoated aluminum side caps and center cross bar
- Mounts to the roof gutter, with a stainless steel gutter mount kit for internal gutters
- Maximum weight capacity 4 lbs; lights sold separately
SKU: CAR210871
Mounting high: pros and cons
A light bar on the windshield cowl or roof throws light far down the trail and over the hood of the vehicle in front, which makes it the favorite spot for a long bar. It also lights up the hood and the dust in front of you, so it glares in rain and fog, and it adds wind noise at highway speed. Bumper and grille mounts avoid the glare but light less distance. Most owners run a roof or cowl bar for the trail and a smaller set of lights lower for everyday use. These mounts are the brackets only; the light bar is sold separately, and the brackets are made for a specific light width.
Types of mount
- Upper windshield mounts bolt to the windshield hinge or frame bolts on a Jeep and hold a bar across the top of the windshield. Rough Country's mounts for the TJ, LJ and JK take a 50 inch straight bar with 50 5/16 inch mounting spacing, single or dual row.
- Roof mounted brackets from N-Fab bolt to the roof or drip rail of a pickup and hold a 49 to 50 3/8 inch side-mount bar above the windshield. They are steel with a zinc coating under the powder coat and sold in pairs for Silverado, Sierra, Ram and the FJ Cruiser.
- Rack brackets from Rhino-Rack clamp lights to Vortex and Heavy Duty crossbars or slide into the channels of a Pioneer platform, for one or two lights up to about 16.5 pounds, and can mount on any side of the tray.
- Cowl mounts for a single 3 inch cube light bolt to the hood hinge, A-pillar, cowl or hardtop on a Jeep.
- Modular roof racks like the N-Fab system for the 4Runner combine a rack with a multi-position light mount.
Getting the size right
Light bars are sold by nominal length but mount by the spacing between their side or end mounts, and the two numbers are not the same. A 50 inch bar from one maker may measure 50 5/16 inches mount to mount and another 52 inches. Measure your bar, or read its mount spacing, and compare with the bracket's listed spacing; N-Fab's roof brackets accept a range from 49 to 50 3/8 inches, which covers most 50 inch bars. Side mount bars need brackets that grab the ends; bottom or slide mount bars need a bracket with a flat or slot. Check the bolt size and whether the bracket is for a straight or curved bar, since Rough Country's windshield mounts are for straight bars.
Installation
Windshield mounts reuse the hinge bolts on a Jeep, so no drilling, but remove one bolt at a time so the windshield frame stays aligned, and torque them to the factory figure. Roof brackets on pickups bolt through the drip rail or roof; use the sealing washers supplied and seal any holes, because a leak here lands on the headliner. Rack brackets clamp or slide into channels with the hardware supplied, which includes shake-proof washers on some Rhino-Rack pieces for a reason: vibration at speed loosens light mounts. Route the harness along the A-pillar under a trim strip or through a wiper arm grommet, with a relay and a fuse, and a switch that cannot be bumped on. Aim the bar on a level road at night so the hot spot sits where you need it and not in the eyes of other drivers.
Rules of the road
Off-road lights above the headlights are generally for off-road use only, and many states require them covered on public roads or restrict their use. Rules vary by state, so check local regulations and fit covers if required.
Popular Roof and Windshield Lighting Mounts brands
- Rhino-Rack USA (5)
- N-Fab (4)
- Go Rhino (3)
- Westin (2)
- Dee-Zee (2)
- Rough Country (2)
- Carr (1)
- Addictive Desert Designs (1)
- DV8 Offroad (1)
- Fishbone Offroad (1)
- Nfab (1)
- Piaa Lighting (1)
Roof and Windshield Lighting Mounts FAQ
Will a 50 inch light bar fit these windshield and roof mounts?
Most 50 inch bars fit, but check the mount spacing rather than the nominal length. Rough Country's Jeep windshield mounts list 50 5/16 inches between mounts for a straight bar, and N-Fab's roof brackets accept 49 to 50 3/8 inches. Measure your bar's mounting points.
Do windshield light bar mounts require drilling on a Jeep?
No. The Rough Country mounts for the TJ, LJ and JK bolt to the existing windshield hinge bolts. Replace one bolt at a time so the frame does not shift, torque to the factory specification and route the wiring down the A-pillar under the trim.
Can I mount lights on a Rhino-Rack Pioneer platform?
Yes. Rhino-Rack sells brackets that slide into the Pioneer channels on any side and at different heights for work lights, spot lights and small LED bars, and clamp-on brackets for Vortex and Heavy Duty crossbars rated for lights up to about 16.5 pounds.
Do roof mounted light bars cause glare or wind noise?
They can. A bar above the windshield lights the hood and the dust in front of you, which reflects in rain and fog, and a bare bar whistles at highway speed. Aim the bar carefully, add a wind deflector or cover for daily driving and keep a lower set of lights for weather.









