Electrical
Showing 145–156 of 171 resultsSorted by popularity
-
Switch Pods
Daystar Dash Switch Panel – KJ71034TN
- Tan dash switch panel mounted in front of the shifter
- Holds up to 5 rocker switches for fog lights and air compressors
- Fits the Jeep Wrangler JK, 2007-2018
- 2-door and 4-door models, automatic transmissions only
- Rocker switches sold separately
SKU: DAYKJ71034TN -
Switch Pods
Daystar Switch Panel with 4 Switches (Black) – KJ71038BK
- Black dash switch panel for 2011–2012 Jeep Wrangler JK
- Holds up to five rocker switches in front of the shifter
- Kit includes one red, one blue, one amber and one green switch
- Installs with the factory clips, made in the USA
- Daystar part KJ71038BK, UPC 618089004514
SKU: DAYKJ71038BK -
-
-
-
Switches
Oracle Lighting Pre-Wired On/Off Flush Mount LED Switch (Amber) – 2012-005
- Oracle Lighting 2012-005 amber pre-wired flush mount LED on/off switch
- Needs a 16MM mounting hole; 12-volt
- Amber / orange glowing power ring
- Universal fit with no year, make or model attached
- Heavy-duty brass assembly, nickel plate finish
SKU: ORC2012-005 -
Switches
Oracle Lighting Pre-Wired On/Off Flush Mount LED Switch (Green) – 2012-004
- Oracle Lighting 2012-004 green pre-wired flush mount LED on/off switch
- Needs a 16MM mounting hole; 12-volt
- Glowing green power ring when activated
- Universal fit with no vehicles matched to it
- Heavy-duty brass assembly with nickel plate finish
SKU: ORC2012-004 -
Switches
Oracle Lighting Pre-Wired On/Off Flush Mount LED Switch (Blue) – 2012-002
- Oracle Lighting 2012-002 blue pre-wired flush mount LED on/off switch
- Needs a 16MM mounting hole; 12-volt
- Glowing power ring when activated
- Universal fit; no specific vehicle assigned
- Heavy-duty brass assembly with nickel plate finish
SKU: ORC2012-002 -
Switches
Oracle Lighting Pre-Wired On/Off Flush Mount LED Switch (UV/Purple) – 2012-007
- Oracle Lighting 2012-007 pre-wired on/off flush mount LED switch
- UV/Purple illumination, 12-volts, push button
- Requires a 16MM mounting hole
- Heavy-duty brass assembly with nickel plate finish
- Universal fit; not waterproof; UPC 201200720143
SKU: ORC2012-007 -
Switch Pods
Advanced Accessory Concepts Trigger 8′ Extension Connectors – 2007
- Advanced Accessory Concepts Trigger 8 foot extension harness
- 12-gauge male and female connectors
- Sealed wires, waterproof connectors and shielded insulation
- Universal fit, not vehicle-specific
- UPC 858208006931
SKU: AAC2007 -
Parts you will find here
This category groups electrical components that either control accessories or keep an engine running. Typical products include switch pods and control systems that organize accessories, rocker and key switches, fuse blocks, light wiring kits, ignition switches and replacement starters. Browsing the subcategories is the fastest way to find a part type, and product pages give the part number and a vehicle note where it applies.
Accessory control and switching
- Switch panels and pods: collect the controls for lights, compressors and other add-ons into one panel.
- Individual switches: rocker, toggle and key switches. A 16 mm round mounting hole is typical for some flush-mount switches, so check panel cutout dimensions.
- Relays and trigger systems: let a small switch control a high-current load safely.
- Light wiring kits: bundle a harness, relay and switch for fog or driving lights.
Fuses and protection
Every accessory circuit needs a fuse or breaker sized to the wire, not to the device. A fuse block gives accessories a protected power source with labeled positions. Use wire gauge that suits the current and length of the run, since undersized wire heats up and drops voltage. Keep fuses close to the power source, and use grommets and loom where wires pass through metal or cross hot surfaces.
Starting and ignition parts
Starters and ignition switches are matched to the engine and model year. A starter listing may be for a specific engine, such as a 4.0L six-cylinder. Verify the engine, transmission type and mounting configuration before choosing a part number. A slow crank or clicking sound can also come from a weak battery, corroded cables or a bad ground, so test those before replacing a starter.
Fitment and installation
Confirm fitment for your exact year, make, model and engine, and compare the part number with your existing component where possible. Always disconnect the battery before working on the electrical system, use a multimeter to check circuits and avoid overloading circuits. Keep connections clean, crimped and sealed against moisture. If you are not comfortable with automotive wiring, consult a qualified installer, since electrical faults can cause fires.
Common mistakes and troubleshooting
Most electrical problems trace back to connections rather than parts. A corroded ground strap, a loose terminal or a poorly crimped connector can cause dim lights, intermittent switches and no-start conditions that look like part failures. Clean and tighten the basics first.
- Use a multimeter. Check battery voltage (a healthy resting battery is around 12.6 volts) and voltage drop across suspicious cables.
- Do not use household wire or tape. Use automotive-rated wire with insulation suited to heat and oil.
- Avoid tapping into factory wiring with cheap splice connectors for high-current loads.
- Label the circuits and keep a simple wiring diagram of what you add.
- Protect connections with dielectric grease or sealed connectors in damp areas.
- Replace damaged or brittle insulation on older vehicles before it causes a short.
When buying parts for an older vehicle, compare the connector shape and the number of terminals with your existing part, because small plug differences are common between model years.
Popular Electrical brands
- Painless Wiring (42)
- SPOD (42)
- Rugged Ridge (32)
- Crown Automotive (29)
- Omix-Ada (17)
- Daystar (13)
- ARB 4x4 Accessories (10)
- Advanced Accessory Concepts (8)
- Oracle Lighting (6)
- Powermaster (3)
- Warn (1)
- Flex-A-Lite (1)
Shop Electrical by type
- Switch Pods (76)
- Switches (35)
- Ignition Switch (15)
- Engine Wiring Harness (0)
- Indicators (9)
- Fuse Block (4)
- Starter Components (6)
- Starter (6)
- Dual Battery Isolator (2)
- Wire Sleeve (3)
- Toggle Switch Panel (1)
- Generator Bushing (3)
- Distributor Lead (2)
- Firewall Grommet (2)
- Quick Connect Booster Assembly (2)
- Electrical Connector (2)
- Fuses (2)
- Multifunction Turn Signal Switch (1)
Electrical FAQ
What is the difference between a switch pod and a fuse block?
A switch pod holds the controls for accessories, while a fuse block distributes protected power to circuits. Many systems combine both functions, and either may be paired with relays for high-current loads.
How do I choose wire and fuse sizes for accessories?
Base the fuse on the wire's current rating and protect the circuit, then size wire gauge for the load and the run length. Check the accessory's current draw and the manufacturer's recommended wiring.
Why does my vehicle click but not start?
Common causes are a weak battery, corroded or loose battery cables, bad grounds or a failing starter or solenoid. Test the battery and connections first before replacing a starter.
Will a starter fit any engine in my model?
No. Starters are matched to the engine, transmission and mounting. Confirm fitment for your exact year, make, model and engine, and compare the part number or mounting with your existing starter.











