Electrical
Showing 169–171 of 171 resultsSorted by popularity
-
Switch Pods
Advanced Accessory Concepts Trigger Accessory Control System – 2001
- Controls up to 24 accessories with one or more control boxes and remotes
- Four solid state relay channels: two 30 amp and two 10 amp
- Battery-powered RF remote with backlit buttons
- Bluetooth app control for on/off, dimming and flashing
- Advanced Accessory Concepts part 2001, UPC 858208006702
SKU: AAC2001 -
Switch Pods
SPOD 2009-2015 JK Wrangler 8 Circuit SE- Special Edition System with Blue LEDs – 8-600-0915-LEDB
Switch PodsSPOD 2009-2015 JK Wrangler 8 Circuit SE- Special Edition System with Blue LEDs – 8-600-0915-LEDB
- Eight-circuit SE switch panel for 2009–2016 Jeep Wrangler JK
- Circuits rated 30 amps at 12.5 VDC each, expandable to 32
- Low-voltage cutoff at 11.2 VDC with a two-minute delay
- Blue LED indicator lights, 100 amp maximum system capacity
- SPOD part 8-600-0915-LEDB, UPC 700007270471
SKU: POD8-600-0915-LEDB -
Switch Pods
SPOD 8 Circuit SE System with Touch Screen and Bluetooth – 8-700-TSB-UNI
- 8-circuit SE touchscreen system with 3.5-inch Bluetooth controller
- Controls up to 32 circuits with a swipe-select screen
- Universal truck application with articulating mount
- Voltage, board temperature and On Road/Off Road safety functions
- SPOD part 8-700-TSB-UNI, UPC 700008512291
SKU: POD8-700-TSB-UNI
Parts you will find here
This category groups electrical components that either control accessories or keep an engine running. Typical products include switch pods and control systems that organize accessories, rocker and key switches, fuse blocks, light wiring kits, ignition switches and replacement starters. Browsing the subcategories is the fastest way to find a part type, and product pages give the part number and a vehicle note where it applies.
Accessory control and switching
- Switch panels and pods: collect the controls for lights, compressors and other add-ons into one panel.
- Individual switches: rocker, toggle and key switches. A 16 mm round mounting hole is typical for some flush-mount switches, so check panel cutout dimensions.
- Relays and trigger systems: let a small switch control a high-current load safely.
- Light wiring kits: bundle a harness, relay and switch for fog or driving lights.
Fuses and protection
Every accessory circuit needs a fuse or breaker sized to the wire, not to the device. A fuse block gives accessories a protected power source with labeled positions. Use wire gauge that suits the current and length of the run, since undersized wire heats up and drops voltage. Keep fuses close to the power source, and use grommets and loom where wires pass through metal or cross hot surfaces.
Starting and ignition parts
Starters and ignition switches are matched to the engine and model year. A starter listing may be for a specific engine, such as a 4.0L six-cylinder. Verify the engine, transmission type and mounting configuration before choosing a part number. A slow crank or clicking sound can also come from a weak battery, corroded cables or a bad ground, so test those before replacing a starter.
Fitment and installation
Confirm fitment for your exact year, make, model and engine, and compare the part number with your existing component where possible. Always disconnect the battery before working on the electrical system, use a multimeter to check circuits and avoid overloading circuits. Keep connections clean, crimped and sealed against moisture. If you are not comfortable with automotive wiring, consult a qualified installer, since electrical faults can cause fires.
Common mistakes and troubleshooting
Most electrical problems trace back to connections rather than parts. A corroded ground strap, a loose terminal or a poorly crimped connector can cause dim lights, intermittent switches and no-start conditions that look like part failures. Clean and tighten the basics first.
- Use a multimeter. Check battery voltage (a healthy resting battery is around 12.6 volts) and voltage drop across suspicious cables.
- Do not use household wire or tape. Use automotive-rated wire with insulation suited to heat and oil.
- Avoid tapping into factory wiring with cheap splice connectors for high-current loads.
- Label the circuits and keep a simple wiring diagram of what you add.
- Protect connections with dielectric grease or sealed connectors in damp areas.
- Replace damaged or brittle insulation on older vehicles before it causes a short.
When buying parts for an older vehicle, compare the connector shape and the number of terminals with your existing part, because small plug differences are common between model years.
Popular Electrical brands
- Painless Wiring (42)
- SPOD (42)
- Rugged Ridge (32)
- Crown Automotive (29)
- Omix-Ada (17)
- Daystar (13)
- ARB 4x4 Accessories (10)
- Advanced Accessory Concepts (8)
- Oracle Lighting (6)
- Powermaster (3)
- Warn (1)
- Flex-A-Lite (1)
Shop Electrical by type
- Switch Pods (76)
- Switches (35)
- Ignition Switch (15)
- Engine Wiring Harness (0)
- Indicators (9)
- Fuse Block (4)
- Starter Components (6)
- Starter (6)
- Dual Battery Isolator (2)
- Wire Sleeve (3)
- Toggle Switch Panel (1)
- Generator Bushing (3)
- Distributor Lead (2)
- Firewall Grommet (2)
- Quick Connect Booster Assembly (2)
- Electrical Connector (2)
- Fuses (2)
- Multifunction Turn Signal Switch (1)
Electrical FAQ
What is the difference between a switch pod and a fuse block?
A switch pod holds the controls for accessories, while a fuse block distributes protected power to circuits. Many systems combine both functions, and either may be paired with relays for high-current loads.
How do I choose wire and fuse sizes for accessories?
Base the fuse on the wire's current rating and protect the circuit, then size wire gauge for the load and the run length. Check the accessory's current draw and the manufacturer's recommended wiring.
Why does my vehicle click but not start?
Common causes are a weak battery, corroded or loose battery cables, bad grounds or a failing starter or solenoid. Test the battery and connections first before replacing a starter.
Will a starter fit any engine in my model?
No. Starters are matched to the engine, transmission and mounting. Confirm fitment for your exact year, make, model and engine, and compare the part number or mounting with your existing starter.

