Select your vehicle
-13%

Rubicon Express CVF Drive Shaft – RE1895-165

Rubicon Express

Shop Jeep Wrangler TJ Drive Shafts on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • CV drive shaft for Jeep Wrangler TJ, 16.5 in long
  • Built for the NP241 transfer case with 1330 and 1350 u-joints
  • Direct, bolt-on fit for Rubicon Express TJ short arm suspension
  • Rear position; slip yoke eliminator required
  • Part RE1895-165, UPC 614901439441

Description

Overview

The shaft is a 16.5 inch CV drive shaft for the 1997–2006 Jeep Wrangler TJ, built to connect an NP241 transfer case. It is a direct, bolt-on shaft for Jeep Rubicon model TJs and is designed for TJ short arm suspension systems.

The shaft uses 1330 and 1350 u-joints and is an extended-length part for the rear position. It requires a slip yoke eliminator, a transfer case part that lets a CV shaft attach directly to the output in place of the slip yoke. The eliminator is not included with this shaft.

Key features

  • CV design with 1330 and 1350 u-joints
  • Direct, bolt-on fit for TJ short arm suspension systems
  • 16.5 inch length
  • Extended length for the rear position
  • Built for the NP241 transfer case

Driveline angles and CV care

A CV shaft runs at angles that change with suspension height and axle position, and those angles affect vibration and joint life. Short arm suspension changes the geometry at the axle, so the shaft length and angles should be checked after installation. A driveline shop can measure the angles and confirm the shaft sits without binding through full suspension travel.

CV joints need clean, intact boots to last. Inspect the boots for cracks or grease leaks, and listen for clicking during tight turns, which can point to a worn joint. Keep the transfer case output and the slip yoke eliminator clean and tight, since a loose connection can cause vibration under load.

  • Measure driveline angles after installation
  • Inspect CV boots for cracks and grease leaks
  • Listen for clicking during tight turns

Specifications

Brand Rubicon Express
Part number RE1895-165
UPC 614901439441
Shaft type CV (constant velocity)
Length 16.5 in, extended
Position Rear
U-joints 1330 and 1350
Transfer case NP241
Slip yoke eliminator Required (not included)

Vehicle fitment

Designed for 1997–2006 Jeep Wrangler TJ models with short arm suspension. Confirm fit for your vehicle’s year, model and trim before ordering.

Confirm your vehicle’s year, model and trim before ordering.

Installation notes

A slip yoke eliminator is required, and it must be bought separately. Because the shaft is built for short arm suspension, check the driveline angles after installing it and correct them before driving on the road. Use a drive shaft installer or shop familiar with CV shafts if the transfer case setup is new to you.

What’s included

One CV drive shaft, 16.5 inches long, with 1330 and 1350 u-joints.

Not included: the slip yoke eliminator, which this shaft requires.

SKU: R/ERE1895-165 Category:

Specification

Shipping weight 19.75 lbs
Package dimensions 16.00 × 6.00 × 4.50 in
brands

Fitment

VehicleYearsTrims
Jeep Wrangler (TJ) likely fits1997–2006All

Vehicles marked "likely fits" are inferred from the product description rather than a manufacturer fitment list. Please confirm fitment with the manufacturer before ordering.

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Does this CV shaft fit a Jeep TJ?

Yes, for the Jeep Wrangler TJ from 1997 to 2006. It is a direct, bolt-on fit for Rubicon model TJs. Match the NP241 transfer case and suspension setup before ordering.

Do I need a slip yoke eliminator with this shaft?

Yes. The shaft requires a slip yoke eliminator, which is sold separately and must be bought along with the shaft.

What length is the shaft?

The shaft is 16.5 inches long and is an extended-length part for the rear position. It uses 1330 and 1350 u-joints.

Is it built for short arm suspension?

Rubicon Express designed the shaft for its TJ short arm suspension systems, so it is intended for that setup. Other suspension setups may need a different shaft length.

What should be checked on a CV shaft after off-road use?

Check the CV boots for tears or grease loss, look for loose bolts at both ends, and watch for vibration at highway speed. Address any boot damage before it lets dirt into the joint.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Jeep Wrangler TJ Drive Shafts on Amazon