Select your vehicle

Crown Automotive Tie Rod Kit – 52000596K

Crown Automotive

$66.20Currently unavailable
Buy on Amazon

See similar parts on Amazon

Price and availability as of Nov 19, 2026 1:10 AM MST, from Amazon.com, and subject to change. The Amazon listing has the current details.

Check out with your Amazon account. Amazon handles delivery and returns.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Fits 1984–1990 Jeep Cherokee XJ and 1986–1990 Comanche MJ
  • Driver-side tie rod kit, knuckle to drag link
  • Includes 2 tie rod ends and adjuster with hardware

Description

Overview

The Crown Automotive 52000596K is a factory-style tie rod kit for the 1984–1990 Jeep Cherokee XJ. The kit spans from the driver-side knuckle to the drag link.

Crown’s copy names the 1984–1990 Cherokee XJ and the 1986–1990 Comanche MJ, and the kit includes 2 tie rod ends and an adjuster with hardware.

Key features

  • Tie rod kit, driver side, knuckle to drag link
  • Includes 2 tie rod ends
  • Includes an adjuster with hardware
  • Factory-style replacement part
  • Direct-fit design

Before replacing the kit

A tie rod kit on a 1980s Cherokee is usually replaced as a set because the tie rod ends wear together. The drag link and the adjuster take the same steering loads, so a worn end often shows up alongside rust or looseness in the adjuster threads. Clean the threads and check the knuckle taper before fitting new ends, since a damaged taper will loosen a new joint quickly. A driver-side kit covers only one side of the linkage, so the opposite side should be inspected at the same time.

Older steering components are often seized, so penetrating oil and patience make removal easier than force. Use new cotter pins or locking hardware where the design calls for it, and tighten nuts to the value in the service manual for your vehicle. After the kit goes in, have the toe set and road-test at low speed to confirm the wheel returns to center. Lubricate the grease fittings on the linkage at regular intervals.

  • Inspect the drag link and pitman arm for play
  • Replace the adjuster if its threads are worn
  • Recheck toe after the first drive

Specifications

Brand Crown Automotive
Part number 52000596K
Part type Tie rod kit
Position Driver side
Span Knuckle to drag link
Contents 2 tie rod ends, adjuster, hardware
Style Factory style
Fit type Direct fit

Vehicle fitment

The kit fits the 1984–1990 Jeep Cherokee XJ and the 1986–1990 Comanche MJ. It spans from the driver-side knuckle to the drag link.

The kit is for the driver side only, and later Cherokee years are not covered. Confirm your vehicle’s year, model and trim before ordering.

What’s included

2 tie rod ends and an adjuster with hardware.

Fitment

VehicleYearsTrims
Jeep Cherokee (XJ)1984–1990Base, Chief, Laredo, Limited, Pioneer, Sport

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

What Jeeps fit Crown 52000596K?

It fits the 1984–1990 Jeep Cherokee XJ and the 1986–1990 Comanche MJ. Later Cherokee years are not covered, so confirm your model year before ordering this kit.

Is Crown 52000596K for the driver or passenger side?

It is for the driver side. The kit spans from the driver-side knuckle to the drag link in the steering linkage, so a passenger-side tie rod needs a different part.

What comes in the Crown 52000596K kit?

The kit includes 2 tie rod ends and an adjuster with hardware. It is a factory-style replacement part, meant to take the place of the original linkage.

Does this kit need a steering alignment?

Yes. Replacing tie rod ends changes the toe setting, so have a shop align the front end after installation. Setting the toe before driving at speed helps prevent uneven tire wear.

Ready to order?

Order this part on Amazon and check out with your Amazon account. Amazon handles delivery and returns.

Buy on Amazon