Overview
The Bilstein 25-177428 is a rear reservoir shock absorber from the 5160 Series for 1999–2006 Chevrolet Silverado 1500 and GMC Sierra 1500 pickups, with 2007 Classic models also on the manufacturer list. It is rated for vehicles with a 4 inch lift and uses an eye mount at both the upper and lower ends, with 13.11 in. of travel between an 18.27 in. collapsed length and a 31.38 in. extended length.
The body is a 46mm ID smooth body with a mono tube design and a remote reservoir. The reservoir gives the shock more oil capacity for heat dissipation and damping sensitivity. The digressive valving produces full damping as soon as the shock moves, and the floating dividing piston in the reservoir allows more shaft movement. The design suits both off-road and on-road driving.
Key features
- Eye mounts at both ends, each 14.4mm
- 13.11 in. travel length between collapsed and extended lengths
- Remote reservoir with floating dividing piston
- Digressive valving for immediate full damping
- Reservoir mounting configuration designed for each vehicle application
- Triple-C Technology zinc plated finish
Eye mounts and hardware
Eye-type mounts depend on the bolt or pin size fitting the eye’s bore, so hardware matters as much as the shock itself. Before ordering replacement bushings or sleeves, measure the eye bore and check that the bolt fits without slop. A sleeve that is too thin for the bore can allow the shock to shift under load.
Rear shock mounts take heavy loads from the axle and bed, so bushing condition affects control and noise. Replace bushings that show cracks, flattened rubber or side play. When a reservoir is involved, check that the hose and reservoir do not touch the frame or driveshaft at full travel, then tighten fasteners after the first few drives.
- Measure eye bore before installing
- Replace cracked or flattened bushings
- Check hose clearance at full extension
- Recheck fasteners after the first drives
Specifications
| Brand | Bilstein |
|---|---|
| Part number | 25-177428 |
| UPC | 651860663791 |
| Series | 5160 Series |
| Position | Rear |
| Collapsed length | 18.27 in. |
| Extended length | 31.38 in. |
| Travel length | 13.11 in. |
| Lower mount | Eye 14.4mm |
| Upper mount | Eye 14.4mm |
| Shaft diameter | 14mm |
| Body design | 46mm ID smooth body (non-coilover) |
| Internal design | Mono tube |
| Reservoir | Yes |
| Charge | Gas charged |
| Finish | Zinc plated |
| Lift height | 4 in. lift |
| Boot included | No |
| Mounting parts included | Reservoir mount kit |
Vehicle fitment
The manufacturer fitment list for this rear shock covers 1999–2006 Chevrolet Silverado 1500 (Base, Hybrid, LS, LT, WT and Z71), 2007 Chevrolet Silverado 1500 Classic (Hybrid, LS, LT and WT), 1999–2006 GMC Sierra 1500 (Base, HT, Hybrid, SL, SLE, SLT and WT) and 2007 GMC Sierra 1500 Classic (Hybrid, SL, SLE, SLT and WT). The 2007 Classic entries are the only model years after 2006 on the list.
Chevrolet Tahoe, Suburban and Avalanche, GMC Yukon and Yukon XL, and 2500 or 3500 series trucks are not on this list, so don’t assume they match. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
The eye-type mounts at both ends must match the 14.4mm eye sizes in the specifications, so check your existing hardware before removing the original shock. The reservoir attaches with the included reservoir mount kit. Support the axle securely before you start, and follow the detailed instructions that come with the shock.
What’s included
Bilstein 5160 Series rear reservoir shock absorber, reservoir mount kit, and detailed instructions.
Not included: A boot.









