Overview
The Baer Brakes 6801273LP is a left port Remaster master cylinder with a 1 inch bore, outlet ports exiting the left side of the body and a 2-bolt flange for GM and Ford firewalls. Its black anodized 6061 T6 billet aluminum body suits brake systems that run long or short boosters, or manual brakes.
Because both outlets leave the left side, plan brake line routing before the unit is bolted in place. The machined billet top is fastened with six allen screws, and two knurled screw-on caps allow fluid to be added without spilling. Inverted flare, banjo and straight fittings can all be used on the 3/8-24 outlet threads, and optional proportioning valves are available.
Key features
- Left side outlet ports on a 1 inch bore body
- One-piece machined body in 6061 T6 billet aluminum
- Two 3/8-24 outlet ports
- Machined, knurled caps that resist fluid spillage during filling
- Laser-etched logos on the anodized finish
- Dual integral reservoir sized at 7oz per reservoir
Master cylinder service basics
A master cylinder converts pedal force into hydraulic pressure for all four wheels, so its condition affects every stop. Inside, piston seals and cups wear over time, and the fluid level in the reservoir drops as pads wear down. Brake fluid absorbs moisture from the air, so periodic fluid replacement helps protect internal surfaces and bleeder fittings from corrosion.
When a system is upgraded with larger calipers, a different booster or a firmer pedal, the cylinder bore and booster push-rod clearance often need to be checked together. Brake lines, proportioning valves and pedal ratio are usually reviewed at the same time, because a change in one alters the pressure the others see.
- Pedal that sinks slowly under steady pressure
- Fluid loss between pad checks
- Fluid seeping from the body or cap seal
- Spongy pedal that persists after bleeding
Specifications
| Brand | Baer Brakes |
|---|---|
| Part number | 6801273LP |
| UPC | 844165051183 |
| Series | ReMaster |
| Bore size | 1 inch |
| Flange type | 2-bolt GM/Ford firewall |
| Body material | 6061 T6 billet aluminum |
| Finish | Black anodized body, lid and caps |
| Outlet port quantity | 2 |
| Outlet port size | 3/8-24 inch |
| Outlet port exit | Left side |
| Outlet port fittings | Banjo without brass seat, 3/16 inch inverted flare and tube nuts with brass seat |
| Reservoir | Dual, integral, 6061 T6 billet aluminum |
| Reservoir size | 7oz per reservoir; fill to 75 percent or 5.25oz per reservoir |
| Stroke | 1.1 |
| Area | 0.78 |
| Volume ratio | 0.0840277777777778 |
| Emission code | 6 |
| Grade | Premium |
| Country of origin | US |
Vehicle fitment
It is built for 2-bolt Ford and GM firewall installations with long or short boosters or manual brake systems. Confirm fit for your vehicle’s year, model and trim before ordering.
Measure your firewall, booster and push-rod length before installing. Confirm fit for your vehicle’s year, model and trim before ordering.
Installation notes
- Long push-rod hydro-boost and vacuum boosters may need spacer p/n 6260258 so the cylinder sits clear of the booster push-rod.
- The brass seats and tube nuts serve the 3/16 inch inverted flare outlet, while a banjo outlet works without the seat.
- Plan line bends for left side outlets so the hard lines clear chassis and steering components.
What’s included
One left port master cylinder assembly with integral dual reservoir, master cylinder cap, two brass seats and two tube nuts. The reservoir and fittings are part of the package.
Not included: a brake booster, any gasket or seal, mounting hardware, the bleeder screw and bleeder hoses, a brake pressure switch, a sensor, a warning light connector, and spacer p/n 6260258.














