Overview
The Baer Brakes 6805199LP is a Remaster master cylinder with left side ports, a 0.875 inch (7/8 inch) bore and a 2-bolt GM/Ford firewall flange. It is intended for brake setups on many Ford and GM applications, though it is not tied to one specific model year or trim.
Each body is one compact piece of 6061 T6 billet aluminum with a black anodized look. A billet top, fixed with six allen screws, carries two knurled screw-on caps that make topping up easy. The outlet ports suit inverted flare lines with removable seats, banjo fittings or straight fittings, and optional proportioning valves are also available.
Key features
- Left side ports
- 2-bolt GM/Ford firewall bracket included
- One-piece machined 6061 T6 billet aluminum body
- Two 3/8-24 outlet ports with removable seats for inverted flare, or banjo and straight fittings
- Knurled caps that fill without spilling fluid
- Laser-etched logos on anodized Remaster bodies
- Compatible with most long and short boosters or manual brake applications
Matching lines and fittings
Port side matters when a left-port cylinder replaces an older unit. The lines have to reach the correct outlets without kinks or strain, so measure the routing before removing old hardware. A short test fit with the cylinder held in place can save time when the bracket and flange are tightened.
Outlet fitting type decides which lines and adapters are needed. Inverted flare connections use seats and tube nuts, while banjo connections use sealing washers and a different outlet arrangement. Mixing the two without the correct adapter invites leaks, so confirm each connection before bleeding.
Booster pushrod length is a common cause of poor pedal feel. A cylinder set too far from the booster can leave the pedal soft, while one set too close can keep the brakes dragging. Take time with that adjustment before the final line work.
- Confirm port side before removing old lines
- Use new seats where flare fittings are reused
- Keep reservoir caps closed during bleeding
- Verify pushrod length before final tightening
Specifications
| Brand | Baer Brakes |
|---|---|
| Part number | 6805199LP |
| UPC | 810215393008 |
| Series | ReMaster |
| Bore size | 0.875 inch (7/8 inch), straight bore |
| Pistons | 2 |
| Material | 6061 T6 billet aluminum |
| Finish | Black anodized body, caps and lid |
| Port exit | Left side |
| Outlet ports | 2, 3/8-24 thread |
| Outlet flare type | Inverted, open |
| Outlet fittings | Banjo without brass seat, 3/16 inch inverted flare and tube nuts with brass seat |
| Flange type | 2-bolt GM/Ford |
| Mounting holes | 2, diameter 0.4 |
| Pedal rod ID | 0.475 |
| Stroke | 1.1 |
| Area | 0.601 |
| Volume ratio | 0.0840277777777778 |
| Reservoir | Integral dual; 7oz per reservoir, fill to 75 percent or 5.25oz per reservoir |
| Removable seats | Yes |
| Emission code | 6 |
| Country of origin | USA |
Vehicle fitment
It suits many Ford and GM applications that use a 2-bolt firewall flange, and it works with most long and short boosters or manual brake setups. Confirm fit for your vehicle’s year, model and trim before ordering.
Confirm your vehicle’s year, model and trim before ordering.
Installation notes
If your booster is a long push-rod design, check whether the 6260258 spacer is needed before final assembly. Flange fasteners are not supplied, so have bolts that suit your firewall on hand. Inverted flare connections use the included brass seats with tube nuts, while banjo connections leave out the seat.
What’s included
One left-port Remaster assembly with the 2-bolt firewall bracket, 2 brass seats and 2 tube nuts, plus the caps and dual integral reservoir.
Not included: the push rod, booster, mounting hardware, optional proportioning valves, pressure switch, spacer 6260258, and any gaskets or seals.














