Overview
The Baer Brakes Remaster 6801298LP is a black anodized, left port master cylinder for 4-bolt Mopar firewall mounts, with a 15/16 inch bore and dual reservoirs. No vehicle years, models or trims are established for it, so confirm fit for your vehicle’s year, model and trim before ordering.
Its body and lid are machined from one piece of 6061 T6 billet aluminum, sized small and compact. The billet top uses 6 allen screws, and the two large knurled screw-on caps make filling easier with less spilling. The cylinder works with most long and short boosters, including setups using the included bullet, and with manual brake systems.
Key features
- Fully machined 6061 T6 billet aluminum construction
- 4-bolt Mopar firewall mounting bracket
- Left side ports, with two 3/8-24 inch outlets
- Outlet choices of banjo without brass seat, or 3/16 inch inverted flare with tube nuts and removable brass seat
- Machined, knurled caps that screw on for filling without spillage
- Black anodized body, caps and lid
- Dual integral reservoir
Choosing a master cylinder
A master cylinder converts pedal force into hydraulic pressure that operates the brakes at each wheel. Its bore size, the number of outlets and the reservoir design all affect how the pedal feels and how the system bleeds. When comparing cylinders, match the mounting style to your firewall first, then confirm that the outlet fittings suit the brake lines you already run.
Compatibility with the booster or manual setup matters as much as the mounting pattern. A cylinder that is too large or too small for the system can produce a soft or hard pedal. Many owners replace the flexible hoses and fittings at the same time, since old hoses can swell and leak under pressure. Check the reservoir fluid level after installation and again after the first few drives.
- Confirm the mounting flange before buying parts
- Match outlet fittings to existing brake lines
- Replace worn hoses and fittings during the same job
- Keep the reservoir cap clean and sealed
Specifications
| Brand | Baer Brakes |
|---|---|
| Part number | 6801298LP |
| UPC | 844165052104 |
| Series | Remaster |
| Body material | 6061 T6 billet aluminum |
| Body color | Black |
| Body finish | Anodized |
| Caps and lid finish | Anodized, black |
| Bore size | 15/16 inch (0.9375 inch) |
| Mounting flange | 4 bolt Mopar |
| Port exit | Left side |
| Outlet port size | 3/8-24 inch |
| Outlet port quantity | 2 |
| Outlet port fittings | Banjo without brass seat; 3/16 inch inverted flare with tube nuts and brass seat |
| Reservoir type | Dual, integral |
| Reservoir material | 6061 T6 billet aluminum |
| Reservoir size | 7oz per reservoir; fill to 75 percent, or 5.25oz per reservoir |
| Removable seats | Yes |
| Stroke | 1.1 |
| Area | 0.69 |
| Volume ratio | 0.0840277777777778 |
| Emission code | 6 |
| Country of origin | USA |
| Box count | 1 |
Vehicle fitment
This cylinder suits many early Mopar applications, as well as long and short boosters and manual brake setups. Those are general uses rather than a specific vehicle match.
Installation notes
Fitting choice comes first: the 3/16 inch inverted flare route uses the included brass seats and tube nuts, while the banjo route is listed without a brass seat. Mounting hardware, a bleeder screw and bleeder hoses are not included, so have them ready before the cylinder goes in. Check each connection for leaks after bleeding and before any road use.
What’s included
One master cylinder assembly with cap, two brass seats and two tube nuts, plus the integral dual reservoir.
Not included: brake booster, bleeder screw, bleeder hoses, brake pressure switch, warning light connector, sensor, gasket or seal, and mounting hardware.













