Select your vehicle

SPOD 8 Circuit SE System with Touch Screen and Bluetooth – 8-700-TSB-JK

SPOD

Shop Jeep Wrangler JK Switch Pods on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Eight-circuit SE touchscreen system for Wrangler JK, 2 and 4 door
  • Covers Wrangler JK from 2007 onward
  • Voltage feedback, board temperature and per-switch amperage
  • Controls up to 32 circuits with a swipe-select touchscreen
  • SPOD part 8-700-TSB-JK, UPC 700008512301

Description

Overview

The SPOD 8 Circuit SE System with Touch Screen and Bluetooth, part 8-700-TSB-JK, is a touchscreen switching system for the Jeep Wrangler JK in 2-door and 4-door bodies, from 2007 onward. It covers the 2007 to 2018 JK range.

The control module is a 3.5-inch LED-backlit TFT LCD with a 320 x 240 resolution and 16.7 million colors, in a billet aluminum case on an articulating mount. A standard 10-foot Ethernet cable runs between the screen and the power distribution module, and Bluetooth LE is built in for customizing the display.

The touchscreen reads battery and alternator voltage and the board temperature, and it shows the amperage of each switch when the system uses the Bantam module. A single screen can control up to 32 circuits, and you move between sources by swiping.

Key features

  • Voltage feedback for battery and alternator
  • Board temperature shown on the screen
  • Per-switch current meter, working with the Bantam module only
  • Three-line legends and icons, set from a smartphone or tablet
  • On Road/Off Road function switch for safety
  • Adjustable backlight timeout, dimming and automatic backlight off
  • Deep sleep after six hours of inactivity or with the engine not running
  • One-touch off, and a one-second hold to shut all circuits down
  • Shuts down automatically when the touchscreen is unplugged

Wiring and power planning

A touchscreen controller is only as good as the wiring behind it. Before mounting, map where the power distribution module will sit, how the switch wiring will reach it and where the Ethernet run will go. Keeping power and signal wiring separate reduces noise and makes troubleshooting easier later.

The per-switch current meter works with the Bantam module, so if that reading matters, plan the power distribution around it. Use fused circuits for each load, keep grounds short and clean, and label every circuit at the module so the screen names match what is wired.

The cabin mount should give clear sight lines from the driver’s seat and stay out of airbag zones and pedal travel. Test every switch on the bench first, then secure the articulating bracket once the cable runs are confirmed.

  • Map the module location before drilling
  • Use fused circuits for each load
  • Label each circuit at the module
  • Keep the screen clear of airbag and pedal areas

Specifications

Brand SPOD
Part number 8-700-TSB-JK
UPC 700008512301
Display 3.5-inch LED-backlit TFT LCD, 320 x 240, 16.7 million colors
Viewing angle 180 degrees
Housing Billet aluminum, articulating mount
Connection Standard 10-foot Ethernet cable
Wireless Bluetooth LE
Circuits Up to 32
Not included Air pressure gauge and power distribution module (SourceSE or Bantam)

Vehicle fitment

It fits Jeep Wrangler JK models from 2007 onward in 2-door and 4-door bodies, which covers the 2007 to 2018 JK years.

Wrangler TJ, LJ and JL models are not covered by these years. Confirm your vehicle’s year, model and trim before ordering.

Installation notes

Plan the 10-foot Ethernet run from the power distribution module to the mounting spot before you fix the articulating bracket, because the screen connects to the module only through that cable.

SKU: POD8-700-TSB-JK Category:

Specification

Shipping weight 6.50 lbs
Package dimensions 12.00 × 12.00 × 7.00 in
brands

Fitment

VehicleYearsTrims
Jeep Wrangler (JK) likely fits2007–2018All

Vehicles marked "likely fits" are inferred from the product description rather than a manufacturer fitment list. Please confirm fitment with the manufacturer before ordering.

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Does this touchscreen fit a 2015 Wrangler JK Unlimited?

Yes. It fits Wrangler JK models from 2007 to 2018 in 2-door and 4-door bodies, which includes the Unlimited four-door. Confirm your vehicle's year, model and trim before ordering.

Is the power module included with the touchscreen?

No. The power distribution module, either SourceSE or Bantam, is not included. The air pressure gauge is also not included with this touchscreen.

Can I customize the switch names on this screen?

Yes. Bluetooth LE is standard for customizing the screen, and each switch's legend and icon can be set from a smartphone or tablet. Up to three lines of legend text are supported.

Does the per-switch current meter need a specific module?

Yes. The per-switch current meter works only with the Bantam module, so plan on a Bantam module if you want that reading.

How should the Ethernet cable be routed?

Route it away from sharp edges, heat sources and moving parts such as the steering column. Leave some slack at each end so the articulating mount can move without strain on the cable.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop Jeep Wrangler JK Switch Pods on Amazon