Select your vehicle

G2 Axle and Gear CORE 44 Front Axle Assembly 4.88 Ratio and Eaton E-Locker – C4TSFS488EC0

G2 Axle and Gear

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • G2 CORE 44 front axle assembly with a 4.88 ratio and an Eaton E-Locker
  • Built for 1997–2006 Jeep TJ/LJ Wranglers and 1984–2001 Jeep XJ Cherokee
  • High pinion Dana 44 gear design in a new CORE 44 housing
  • Accepts stock Dana 44 ring and pinions, axle shafts and aftermarket lockers
  • Part number G/2C4TSFS488EC0

Description

Overview

The G2 Axle and Gear CORE 44 front axle assembly, part number G/2C4TSFS488EC0, has a 4.88 gear ratio and an Eaton E-Locker. G2 introduces its CORE 44 axle housing for 1997-2006 Jeep TJ/LJ Wranglers and 1984-2001 Jeep XJ Cherokee, so the front axle is aimed at owners of those two vehicles.

The housing uses the high pinion Dana 44 gear design, a later generation of that layout. It was built to handle loads that would bend a stock Dana 30 or a Rubicon Dana 44. It accepts stock Dana 44 ring and pinions, stock axle shafts and all aftermarket lockers.

This version is the 4.88 ratio with an Eaton E-Locker. The axle shafts are 30 splines, the wheel bolt pattern is 5 on 4.5 inches, and the brakes are reused from the vehicle.

Key features

  • CORE 44 high pinion Dana 44 housing
  • Accepts stock Dana 44 ring and pinions and axle shafts
  • Accepts all aftermarket lockers
  • Eaton E-Locker traction device
  • 4.88 gear ratio
  • 30 spline axle shafts
  • 5 on 4.5 inch wheel bolt pattern

Gear setup and locker choices

A front axle with a 4.88 ratio and an Eaton E-Locker suits owners who want better low-speed traction on rough ground. The locker engages only when needed, so daily driving stays normal. Gear ratio and tire size should be considered together, since they set how the axle works at low speed.

Because this housing takes stock Dana 44 ring and pinions and aftermarket lockers, future gearing or locker changes are possible. Any ring and pinion change needs proper setup, including carrier bearing preload and backlash, to avoid noise and early gear wear. Keep the axle fluid topped up and look for leaks at the seals.

  • Check axle fluid level and condition
  • Inspect pinion and axle seals for leaks
  • Use a shop with gear setup tools

Specifications

Brand G2 Axle and Gear
Part number G/2C4TSFS488EC0
Axle type CORE 44 front, high pinion Dana 44 design
Housing type 97-06 TJ and 84-01 XJ Dana 44
Position Front
Gear ratio 4.88
Axle spline 30 splines
Traction device Eaton E-Locker
Wheel bolt pattern 5 on 4.5 inches
Brakes Reuse factory

Vehicle fitment

It is built for the 1997–2006 Jeep TJ/LJ Wranglers and the 1984–2001 Jeep XJ Cherokee, covering the 1997–2006 TJ, 2004–2006 LJ and 1984–2001 Cherokee XJ. Confirm fit for your vehicle’s year, model and trim before ordering.

Check your vehicle’s year, model and trim against the TJ, LJ and XJ years above before ordering.

Installation notes

The CORE 44 uses a high pinion Dana 44 gear design, so ring and pinion setup and bearing preload should be handled by a shop with gear setup tools. Because the housing takes stock Dana 44 axle shafts, the existing shafts can be reused if they are in good condition.

What’s included

The CORE 44 front axle assembly with the Eaton E-Locker and 4.88 gears.

Not included: Axle shafts and ring and pinions: check whether they are included before starting.

Fitment

VehicleYearsTrims
Jeep Cherokee (XJ) likely fits1984–2001All
Jeep Wrangler (LJ) likely fits2004–2006All
Jeep Wrangler (TJ) likely fits1997–2006All

Vehicles marked "likely fits" are inferred from the product description rather than a manufacturer fitment list. Please confirm fitment with the manufacturer before ordering.

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Will the G/2C4TSFS488EC0 fit a 2003 Jeep Wrangler TJ?

Yes. G2 introduces the CORE 44 for 1997-2006 Jeep TJ/LJ Wranglers, so a 2003 TJ falls inside that range. Confirm your vehicle's year, model and trim before ordering.

Does the CORE 44 take my existing Dana 44 gears and axle shafts?

The CORE 44 accepts stock Dana 44 ring and pinions and axle shafts, along with all aftermarket lockers. Existing Dana 44 parts can be installed in the new housing, with a proper gear setup.

What gear ratio and locker are on this front axle?

This version has a 4.88 gear ratio and an Eaton E-Locker. The axle shafts are 30 splines, and the wheel bolt pattern is 5 on 4.5 inches.

Can I change the gear ratio later?

Yes, the housing accepts stock Dana 44 ring and pinions, so a different ratio is possible. The change needs proper gear setup, including pinion depth and bearing preload, so have a shop with gear setup tools do the work.

How can I tell the E-Locker is working?

A locker engages under load, so a firm traction change on loose ground is the sign. A clunk or chatter during slow turns can mean the locker is not disengaging. Check the operation against the locker's own instructions.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon