Overview
The Baer Brakes 6801303RP is a Remaster master cylinder with a 1-1/8 inch (1.125 inch) bore, a 4-bolt Mopar firewall flange and right side outlet ports, finished in gray anodized billet aluminum. It is a compact, one-piece unit machined from 6061 T6 billet aluminum, intended for early Mopar brake systems that use either a power booster or a manual pedal setup.
The billet top is fastened with 6 allen screws and carries two large knurled caps, so brake fluid can be added without spilling. The outlet ports use a 3/8-24 thread and accept inverted flare fittings with removable brass seats, or banjo style and straight fittings. It is compatible with most long and short booster or manual applications, and optional proportioning valves are also available.
Key features
- Fully machined 6061 T6 billet aluminum construction
- Right side ports with a 3/8-24 outlet thread
- Removable seats support inverted flare fittings, with banjo or straight fittings also possible
- Machined, knurled screw-on caps for filling without spillage
- Gray anodized body with black anodized caps and lid
- 4-bolt Mopar firewall mounting bracket
Brake fluid and bleeding
Brake fluid is the medium that carries pressure from the master cylinder to the wheel cylinders and calipers, so the reservoir and outlet lines work as one system. Fluid absorbs moisture from the air over time, which lowers its boiling point and can make the pedal feel soft under hard braking. Use fluid from a sealed container and the grade the system calls for, and keep the cap closed except when filling.
Bleeding removes air from the lines after any hydraulic component is replaced. Work through the wheels in the order your service procedure gives, keep the reservoir topped up, and never let it run dry during the job. Old fluid should not be reused, and fluid drawn off during bleeding should be discarded rather than returned to the reservoir.
- Use the fluid grade the system is designed for
- Keep the reservoir topped up while bleeding
- Discard fluid drawn off during the bleed
- Inspect the caps and seats for leaks after filling
Specifications
| Brand | Baer Brakes |
|---|---|
| Part number | 6801303RP |
| UPC | 844165052210 |
| Series | ReMaster |
| Bore size | 1.125 inch (1-1/8 inch) |
| Body material | 6061 T6 billet aluminum |
| Body finish and color | Anodized, gray |
| Cap and lid finish | Anodized, black |
| Flange type | 4 bolt Mopar |
| Master cylinder port exit | Right side |
| Outlet port size | 3/8-24 inch |
| Outlet port quantity | 2 |
| Outlet port fittings | Banjo without brass seat, 3/16 inch inverted flare and tube nuts with brass seat |
| Removable seats | Yes |
| Reservoir | Integral, dual, 6061 T6 billet aluminum |
| Reservoir size | 7 oz per reservoir; fill to 75 percent or 5.25 oz per reservoir |
| Stroke | 1.3 |
| Master cylinder cap | Included |
| Country of origin | USA |
| Sold as | Each |
Vehicle fitment
Many early Mopar models use a 4-bolt firewall flange, which is the pattern this unit is built for. Match your vehicle’s year, model and trim before you order this unit, and measure the flange pattern and bore against your original unit.
Confirm your vehicle’s year, model and trim before ordering.
Installation notes
The two brass seats and two tube nuts in the box go with the inverted flare outlets, so choose the fitting type before routing and tightening the lines. Bleeder screws, bleeder hoses and mounting hardware are not supplied, so have them ready before the install begins.
What’s included
One Remaster master cylinder assembly with its master cylinder cap, two brass seats, two tube nuts and an integral dual reservoir.
Not in the box: the brake booster, bleeder screws, bleeder hoses, a brake pressure switch, a sensor, a gasket or seal, and mounting hardware.














