Overview
The Baer Brakes 6801330LP is a polished ReMaster master cylinder with left side ports and a 1.125 inch (1-1/8) bore, made for the 1999-2004 Ford Mustang hydroboost. It mounts through a two bolt flange designed for the SN95 hydroboost firewall bracket, so it suits that hydroboost setup rather than general use.
Baer Brakes forms the body from one piece of 6061 T6 billet aluminum with a billet top secured by six allen screws. Knurled screw-on caps allow filling without spillage. Choose this left port version when your plumbing has to exit on the left side of the cylinder.
Key features
- Left side port exit for the outlet plumbing
- Two bolt flange for the 1999-04 SN95 Mustang hydroboost
- Machined 6061 T6 billet aluminum body with a polished finish
- Two 3/8-24 outlets, inverted flare with removable brass seats or banjo
- Dual integral reservoirs with knurled, screw-on caps
Left port plumbing
Routing outlet lines on the left side means the hard lines and fittings sit in a different path than a right port layout. Before final tightening, dry-fit the lines so they clear the reservoirs, the booster and any nearby suspension or steering parts. Lines that rub against a moving component can wear through over time, so secure them with clips and keep a gap at full steering lock.
Inverted flare and banjo connections seal in different ways. Flares depend on clean seats and correctly torqued tube nuts, while banjo connections rely on the washers or seals used with them. Replace any washer, seat or nut that is damaged on removal, and inspect the lines for kinks or abrasion before the brakes are road tested.
- Dry-fit lines before final tightening
- Keep lines clear of steering and suspension components
- Replace damaged washers and seats on removal
Specifications
| Brand | Baer Brakes |
|---|---|
| Part number | 6801330LP |
| UPC | 844165054283 |
| Series | ReMaster |
| Bore size | 1.125 inch (1-1/8) |
| Material | 6061 T6 billet aluminum |
| Body finish | Polished |
| Caps and lid finish | Polished |
| Port exit | Left side |
| Outlet ports | 2 at 3/8-24 |
| Outlet fittings | Banjo without brass seat; 3/16 inch inverted flare with tube nuts and brass seat |
| Reservoir | Dual integral; 7oz per reservoir, fill to 75 percent or 5.25oz per reservoir |
| Flange | 2 bolt, 1999-04 SN95 Mustang hydroboost specific |
| Removable seats | Yes |
| Stroke | 1.3 |
| Area | 0.97 |
| Country of origin | USA |
Vehicle fitment
The cylinder is written up for the 1999-2004 Ford Mustang Cobra hydroboost application, and its flange is specific to 1999-04 SN95 hydroboost systems. There is no structured fitment list attached, so verify the model year and the SN95 bracket by sight before ordering.
Mustangs outside 1999-04 and brake systems without the SN95 hydroboost bracket are not covered by this flange. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
Mount the cylinder on the SN95 hydroboost bracket first, then assemble the outlet fittings on the left side. Banjo fittings take no seat, while inverted flare fittings need the two brass seats and tube nuts that come with the unit. Check that the lines clear the reservoirs and fill to the 75 percent mark. Brake components affect stopping, so a qualified technician should confirm the finished installation.
What’s included
One ReMaster master cylinder assembly with cap, two brass seats and two tube nuts.
Not included: a booster, any mounting hardware, a bleeder screw with hoses, and a brake pressure switch.













