Overview
The Baer Brakes 6805199RP is a Remaster master cylinder with a 0.875 inch (7/8 inch) bore, a 2-bolt GM/Ford mounting flange and right side ports. Baer aims it at brake systems on many Ford and GM applications, but no specific model years or trims are named.
The body is a small, compact, one-piece block machined from 6061 T6 billet aluminum and finished in black anodized coating. Two large knurled screw-on caps sit on the billet top, which is held by 6 allen screws, so the reservoirs can be filled without spillage. Each outlet port accepts either inverted flare or banjo style fittings, and optional proportioning valves are also available.
Key features
- 2-bolt GM/Ford firewall mounting bracket included
- Fully machined 6061 T6 billet aluminum construction
- Outlet ports use 3/8-24 threads for inverted flare (with removable brass seats), banjo or straight fittings
- Right side ports
- Machined, knurled screw-on caps for filling without spillage
- Anodized finish with laser-etched logos
- Dual integral reservoirs and two pistons
Bench bleeding and setup
Bench bleeding a master cylinder before it goes on the car removes air from the bores and gives a firmer first pedal. Mount the cylinder upright, fill both reservoirs with fresh fluid, and cycle the piston slowly with the outlet ports open until no bubbles come out. Keep the caps on between steps so fluid does not spill onto paint.
Pedal rod length and booster interaction matter as much as bore size. A rod set too far in or out can cause the piston to bottom or fail to return, so set it before tightening the flange. Inverted flare lines should be checked for clean, undamaged seats before they are reconnected.
- Replace the fluid whenever the hydraulic system is opened
- Keep reservoir caps seated to limit moisture
- Check that the flange seats squarely on the firewall
- Recheck line fittings after the first drive
Specifications
| Brand | Baer Brakes |
|---|---|
| Part number | 6805199RP |
| UPC | 810215393015 |
| Series | Remaster |
| Bore size | 0.875 inch (7/8 inch), straight bore |
| Pistons | 2 |
| Material | 6061 T6 billet aluminum |
| Finish | Black anodized body, caps and lid |
| Port exit | Right side |
| Outlet ports | 2, 3/8-24 thread |
| Outlet flare type | Inverted, open |
| Outlet fittings | Banjo without brass seat, 3/16 inch inverted flare and tube nuts with brass seat |
| Flange type | 2-bolt GM/Ford |
| Mounting holes | 2, diameter 0.4 |
| Pedal rod ID | 0.475 |
| Stroke | 1.1 |
| Area | 0.601 |
| Volume ratio | 0.0840277777777778 |
| Reservoir | Integral dual; 7oz per reservoir, fill to 75 percent or 5.25oz per reservoir |
| Removable seats | Yes |
| Emission code | 6 |
| Country of origin | USA |
Vehicle fitment
It suits many Ford and GM applications that use a 2-bolt firewall flange, and it works with most long and short boosters (using the included bullet) or manual brake setups. Confirm fit for your vehicle’s year, model and trim before ordering.
Confirm your vehicle’s year, model and trim before ordering.
Installation notes
Some long push-rod hydro-boost and vacuum boosters need an additional spacer, Baer part 6260258, to space the Remaster away from the booster push-rod. Mounting hardware is not included, so the flange will need fasteners sized for your firewall. Inverted flare lines use the brass seats and tube nuts provided, while banjo lines use the banjo outlet without a seat.
What’s included
One Remaster master cylinder assembly with the 2-bolt GM/Ford firewall mounting bracket, 2 brass seats, 2 tube nuts and the attached dual reservoirs and caps.
Not included: mounting hardware, push rod, brake booster, brake pressure switch, bleeder screw and hoses, dust boot, gasket or seal, and the 6260258 spacer, which some boosters need.














