Shock boots keep grit and water off a lifted shock's shaft and seal. How to size, vent and inspect one, when it can trap…
Shock Absorbers
Showing 1537–1548 of 3453 resultsSorted by popularity
-
-
Shock Absorbers
Rancho RS5000 Series Shock Absorber – RS5134
- Rancho RS5134 gas-charged shock from the RS5000 Series
- Built to suit both stock and raised light trucks and SUVs
- Ten-stage velocity sensitive valving
- 1 3/8-in. (35mm) piston with 5/8-in. (16mm) piston rod
- Red protective boot included; no vehicle list is provided
SKU: RANRS5134 -
Shock Absorbers
Rancho RS5000 Series Shock Absorber – RS5125
- Rancho RS5125 shock absorber from the RS5000 Series, a hydraulic, gas-charged design
- Ten-stage velocity sensitive valving
- 5/8-in. (16mm) diameter piston rod and 1 3/8-in. (35mm) diameter piston
- Red protective boot included
- Confirm fit by year, make, model and trim before ordering
SKU: RANRS5125 -
Shock Absorbers
Rancho RS5000 Series Shock Absorber – RS5124
- Rancho RS5124 rear gas-charged shock, RS5000 Series
- Fits 1992–2005 Chevrolet Blazer, 1995–2000 Tahoe and 1992–2000 GMC Yukon
- Also fits 1999–2000 Cadillac Escalade and 1992–1999 Suburban models
- Lift rating w/0 in. Lift/Drop
- Ten-stage velocity sensitive valving, red protective boot included
SKU: RANRS5124 -
Shock Absorbers
Rancho RS5000 Series Shock Absorber – RS5117
- Rancho RS5117 front gas-charged shock, RS5000 Series
- Fits 1966–1996 Ford Bronco, 1977–1996 F-150 and 1980–1996 F-250
- Also fits 1983–1992 Ford Ranger and 1971–1980 International Scout II
- Lift rating w/0 in. Lift/Drop
- Red protective boot included
SKU: RANRS5117 -
Shock Absorbers
Rancho RS5000 Series Shock Absorber – RS5114
- Rancho RS5114 from the RS5000 Series shock absorber line
- Ten-stage velocity sensitive valving with 1 3/8-in. (35mm) piston
- 5/8-in. (16mm) diameter piston rod
- Red protective boot included
- No vehicle fitment listed; check manufacturer specifications
SKU: RANRS5114 -
Shock Absorbers
Rancho RS5000 Series Shock Absorber – RS5111
- Rancho RS5111 front gas-charged shock, RS5000 Series
- Lift rating w/0 – 2 in. Lift
- Vehicle fitment for this part number is not yet established; confirm fit before ordering
- Ten-stage velocity sensitive valving with a 5/8-in. (16mm) piston rod
- Red protective boot included
SKU: RANRS5111 -
Shock Absorbers
Rancho RS5000 Series Shock Absorber – RS5041
- Rancho RS5041 rear shock from the gas-charged RS5000 Series
- Fits 2000–2006 Toyota Tundra Base, Limited and SR5 models
- Lift rating w/0 in. Lift/Drop
- Ten-stage valving, 5/8-in. (16mm) piston rod, 1 3/8-in. (35mm) piston
- Red protective boot included
SKU: RANRS5041 -
Shock Absorbers
Rancho RS5000 Series Shock Absorber – RS5040
- Rancho RS5040 rear gas-charged shock absorber from the RS5000 Series
- Fits the 2000–2006 Toyota Tundra in Base, Limited and SR5 trims
- Lift rating w/0 in. Lift/Drop
- Ten-stage velocity sensitive valving with a 1 3/8-in. (35mm) piston
- Red protective boot included
SKU: RANRS5040 -
Shock Absorbers
Rancho RS5000 Series Shock Absorber – RS5014
- Rancho RS5014, part of the RS5000 Series shock absorber line
- Ten-stage velocity sensitive valving
- 5/8-in. (16mm) diameter piston rod and 1 3/8-in. (35mm) diameter piston
- Red protective boot included
- Fitment not listed; check manufacturer specifications before ordering
SKU: RANRS5014 -
Shock Absorbers
Rancho RS5000 Series Shock Absorber – RS5010
- Rancho RS5010 rear gas-charged shock absorber, RS5000 Series
- Fits 1997–2004 Dodge Dakota and 1998–2003 Dodge Durango
- Also fits 1983–1992 Ford Ranger, 1994–1996 Mazda B3000 and 1994–1997 Mazda B4000
- Ten-stage velocity sensitive valving with a 5/8-in. (16mm) piston rod
- Lift rating w/2.5 in. lift; red protective boot included
SKU: RANRS5010 -
Shock Absorbers
Rancho RS5000 Series Shock Absorber – RS5005
- Rear gas-charged shock for Dodge Ramcharger and Dodge W100 through W350 trucks
- Also fits the 1976–1981 Plymouth Trailduster
- Lift range w/0 – 4 in. Lift, direct fit
- Ten-stage velocity sensitive valving, red protective boot
- Part number RS5005, UPC 10039703500507
SKU: RANRS5005
What a shock absorber does
A shock absorber is a damper. The spring holds the vehicle up, and the shock controls how fast that spring moves. Without working dampers a truck bounces repeatedly after every bump, tires lose contact with the ground, and braking and steering suffer. Off-road, shocks also absorb heat from constant motion, which is why fade becomes a concern on long, rough stretches.
Key specifications to compare
- Collapsed and extended length: These two numbers set the travel (extended minus collapsed). The shock must be long enough that it never limits suspension travel or bottoms out before the bump stops do, and short enough that it is not the first thing to run out at full droop.
- Mounts: Bar pin, stem, eyelet and bolt-in ends are not interchangeable without hardware. Match both the upper and lower mount styles to your vehicle.
- Body design: Monotube shocks usually run cooler and resist foaming better. Twin-tube shocks are common as stock replacements and are often quieter and lower in cost. Many listings state the body diameter, such as a 46mm smooth body.
- Reservoir: An external reservoir adds oil volume and gas capacity, which helps with heat in hard or sustained use.
- Shaft diameter: A larger shaft is generally more resistant to bending.
Choosing for your use
For a daily driver with a modest lift, a quality non-adjustable monotube or gas-charged twin-tube shock sized for your lift height is usually enough. If you tow, carry a heavy bumper and winch, or run fast desert roads, look at larger bodies, reservoirs and tunable valving. Pair the shock with the right spring rate; a shock cannot make up for a spring that is too soft or too stiff for the load.
Fitment and installation
Shocks are specific to lift height, axle and whether they are front or rear, so confirm fitment for your exact year, make and model and check the manufacturer's specifications. Replace shocks in axle sets, since one new and one worn shock gives uneven handling. Support the axle before removal so it cannot droop and stretch brake lines, and tighten fasteners to the specified torque. If you changed ride height, have the alignment checked afterward.
A final point on tuning: if a shock offers adjustable damping, change one setting at a time and note the result on a familiar road. Heavier loads, such as a winch bumper, roof tent or camping gear, often call for firmer valving than an empty truck. Inspect boots, bushings and mounting hardware at every oil change, since a worn bushing can mimic a failing shock.
Mistakes to avoid
The most common error is choosing shocks by brand or price without checking the length numbers. A shock that is too short lets the axle droop until the springs unseat or brake lines tighten, while one that is too long bottoms out and can bend the shaft or damage the mounts. Measure from mount to mount at ride height, then at full droop and full compression, and compare with the listed collapsed and extended lengths.
- Do not ignore worn bushings, since new shocks with tired bushings still clunk.
- Do not use a shock as a travel limiter; bump stops and limit straps do that job.
- Do not install shocks with the vehicle hanging from the frame and the springs unloaded, because mounts then sit in the wrong position.
Test drive on a familiar road after installation and listen for rattles before heading onto the trail.
Related guides
- Shock Boots: Why Every Lifted Shock Needs One
- Jeep JK Lift Heights: 2.5 vs 3.5 vs 4.5 Inch Compared
Jeep JK lift heights compared: the tires 2.5, 3.5 and 4.5-inch lifts clear, the track bars, arms, lines and driveshafts each needs, and which…
- Twin-Tube, Monotube or Reservoir: Picking the Right Shock
Twin-tube, monotube and reservoir shocks compared: how each handles heat, how to size one for your lift, and which design fits how you drive.
- Bilstein 5100 vs Fox 2.0 Performance: Which Shock for Your Lifted Truck or Jeep
Bilstein 5100 vs Fox 2.0 Performance: body, shaft, reservoir, travel and lift ratings across 417 part numbers, which trucks and Jeeps both fit, how…
Popular Shock Absorbers brands
- Pro Comp Suspension (898)
- Bilstein (615)
- Rancho (567)
- Fox Racing Shox (345)
- Skyjacker (279)
- Fabtech (232)
- ARB 4x4 Accessories (136)
- FOX (85)
- ICON Vehicle Dynamics (84)
- Rubicon Express (78)
- Icon Suspension (77)
- King Shocks (71)
Shock Absorbers FAQ
How do I know when shocks are worn out?
Common signs are oil leaking down the body, a bouncy or floaty ride, nose dive under braking, uneven tire wear and clunking from the mounts. A worn shock may also feel hot or weak when you compare it with a new one.
What is the difference between monotube and twin-tube shocks?
A monotube has a single working chamber with a floating piston separating oil and gas, which tends to shed heat well. A twin-tube uses an inner and outer tube and is common in factory-style replacements. Both can work well when matched to the vehicle.
Do I need new shocks after a lift?
Usually yes. A lift changes the distance between the mounts, so stock shocks may limit travel or bottom out. Choose shocks whose collapsed and extended lengths suit your lift height, and confirm the specifications with the manufacturer.
Should shocks be replaced in pairs?
Yes, replace both shocks on an axle together. Mixing new and worn dampers makes the two sides react differently, which affects handling and braking stability, especially on rough surfaces.













