Select your vehicle

Showing 13–22 of 22 resultsSorted by popularity

What a spring hanger does

A leaf spring attaches to the frame at two points. The fixed end, the main eye, bolts into a hanger welded or riveted to the frame and sets the axle's fore-and-aft position. The other end hangs from a shackle that swings in a shackle bracket so the spring can lengthen as it flattens under load. Both brackets take every pothole, rock strike and winch pull through the spring, and on a Jeep or Toyota that has spent decades off road, they crack at the welds, rust through at the frame or tear where the bolt passes. The parts here replace them with factory-style pieces or heavier fabricated ones, and a few are part of a lift system.

Factory-style replacements

  • Main eye hangers: Omix-ADA's main eye hanger fits the front or rear main eye on Jeep applications, one per spring. Crown's spring hanger bracket for the 1987 to 1995 YJ is a main eye bracket that requires welding to the frame.
  • Shackle brackets: Omix-ADA's unthreaded rear shackle bracket and Crown's rear shackle end hanger are factory replacement designs; unthreaded means the bolt passes through with a nut rather than threading into the bracket.
  • Pivot brackets: Crown's A500 and Omix-ADA's pivot bracket for 1941 to 1968 Willys MB, CJ-2, CJ-3 and CJ-6 are the early design with a pivot pin.
  • Rear frame hangers: Crown's frame-mounted rear hanger covers the 1976 to 1983 CJ5, 1976 to 1986 CJ7 and 1981 to 1985 Scrambler.

Several listings are marked direct fit without naming the vehicle, so compare the shape, bolt spacing and frame contour with your old bracket before choosing.

Heavy-duty and lift hangers

Mountain Off Road Enterprises makes front shackle hangers in chrome-moly steel for the 1976 to 1986 CJ5 and CJ7 and the 1987 to 1995 YJ, sold in pairs, in bare steel or powder coat. They replace the thin factory stamping with a thicker bracket that resists tearing when the shackle is loaded sideways on a rock, and they work with stock or lift springs. Trail Gear's welded 1/4 inch plate spring hanger kit for the 1986 to 1995 Toyota pickup and 4Runner is made for 3 to 6 inch aftermarket lift springs on the solid front axle and replaces hangers that are commonly ripped off those trucks. Pro Comp's rear spring hanger kit includes hangers, shackles, long sway bar links and shocks as the rear half of its 6.5 inch suspension system; it is not a standalone replacement.

Welding and installation

Most frame hangers are welded, and even bolt-in replacements often need the old rivets or welds cut off. Support the frame on stands, remove the spring, grind the old bracket flush and clean the frame to bare metal. Clamp the new hanger in position using the spring and axle as a reference so the axle stays centered and square, and tack it before full welding. Disconnect the battery and protect fuel and brake lines from heat. A frame weld on a suspension bracket is structural; if you are not confident in your welding, have a fabrication shop do it. Paint the area afterward to stop rust at the heat-affected zone.

Checks after the job

With the vehicle on the ground, verify the spring eye bolts are torqued to specification, the shackle swings freely without binding at full compression and droop, and the axle is centered side to side and the wheelbase matches on both sides. Drive gently and recheck torque after 100 miles. Confirm the hanger matches your exact year, model, position and spring type before choosing.

Popular Leaf Spring Hanger brands

Leaf Spring Hanger FAQ

How do I know a spring hanger is failing?

Look for cracks in the bracket or the frame around it, elongated bolt holes, rust scaling that leaves the metal thin, or a bracket that has pulled away from the frame so the spring eye sits crooked. A clunk over bumps, a shift in axle position or uneven wheelbase side to side are symptoms.

Do I have to weld a spring hanger to the frame?

On most Jeeps and Toyotas the factory hangers are welded or riveted, and the replacements are welded in. Some kits are designed to bolt through the frame. The listing for the YJ bracket here specifically says welding is required. If you do not weld, have a fabrication shop fit it.

Should I replace both hangers on an axle at once?

If one side has cracked or rusted through, the other side has seen the same conditions and is likely weak. Replacing both keeps the axle square and avoids a second repair later. Heavy-duty hangers are sold in pairs for this reason.

Will a heavy-duty hanger change my ride height?

Factory-style and heavy-duty replacement hangers put the spring eye in the stock location, so ride height stays the same. Hangers sold as part of a lift kit, like the Pro Comp rear kit, relocate the eye and are designed for that kit's springs and shackles only.