Differential Gear Kit
Showing 25–28 of 28 resultsSorted by popularity
-
-
-
Differential Gear Kit
Dana Spicer Dana 30 Open Differential Internal Kit – 706010X
- Internal kit for open Dana 30 differentials
- Two spider gears and two 27 spline side gears, each with shims
- Includes a cross shaft and cross shaft retainer pin
- For open differentials only; not for limited slip cases
SKU: D/S706010X -
Dana 44 Open Differential Parts
Dana Spicer Dana 44 Open Differential Internal Kit – 706027X
- Dana Spicer Dana 44 open differential internal kit, part 706027X
- Two spider gears with shims, two 30 spline side gears with shims
- Cross shaft and retainer pin included
- For open differentials only
SKU: D/S706027X
What is in a differential gear kit
The differential allows the left and right wheels to turn at different speeds in a corner. Inside the carrier, spider gears mounted on a cross shaft mesh with two side gears that the axle shafts spline into. A gear kit replaces these internal parts, and a typical open differential kit contains two spider gears, two side gears, shims, a cross shaft and a retainer pin. Some kits are for limited-slip units and include clutch discs.
When these kits are used
- Repair: broken or chipped spider gears after a hard hit or a failed axle shaft.
- Rebuild: worn gears or side gear splines during a differential service.
- Axle upgrade: moving to higher-spline side gears when fitting stronger axle shafts. Spline counts such as 27, 30 and 35 are common.
- Limited-slip service: Trac-Lok and Power Lok gear and disc sets restore a clutch-type limited-slip.
Specs that must match
- Axle model: Dana 30, 35, 44, 60, Ford 8.8 and 9 inch, GM 7.5, 8.25 and 8.6 inch, Chrysler 8.25 and 9.25 inch, and AMC 20 are different designs and not interchangeable.
- Spline count: the side gears must match the axle shaft spline count.
- Carrier fit: the kit needs to suit the carrier case and its ratio, and some designs fit all ratio carrier cases.
- Open or limited-slip: check whether the kit is for an open differential only.
- Cross shaft diameter and pin: these differ between axle types and years.
Installation notes
Differential work is precision work. Backlash and ring and pinion contact patterns must be set according to specification, and the carrier bearings and ring gear bolts need correct torque. Tools such as a dial indicator, bearing pullers and a press are typical. If you are not experienced with gear setup, a qualified drivetrain shop is a better choice, since mistakes can destroy a ring and pinion.
Use fresh gear oil, with the correct friction modifier for limited-slip units, and follow the manufacturer's break-in guidance. A kit does not by itself change gear ratio or add a locking function.
Confirm fitment for your exact year, make, model and axle, and read the manufacturer's specifications, then compare the products below.
Inspection and break-in
Before ordering a kit, pull the differential cover and inspect the parts. Metal in the fluid, chipped teeth or scored shafts point to deeper problems that a gear kit may not fix alone. It is usually wise to replace the carrier bearings, seals and gaskets while the differential is open, and to inspect the ring and pinion.
After assembly, drive gently for the first few hundred miles and avoid hard launches or heavy towing. Change the gear oil after the initial break-in as the manufacturer recommends, since early fluid collects small metal particles.
Document everything as you work. Note the shim locations, the position of each gear and the original backlash and contact pattern, and keep parts organized on a clean bench. Check the carrier case for cracks and the cross shaft bore for wear, since new gears in a worn case will fail early. Use only the shims and hardware specified for your axle.
Popular Differential Gear Kit brands
Differential Gear Kit FAQ
What is the difference between an internal kit and a carrier?
An internal kit holds the gears, shims and shaft that sit inside a carrier case. A carrier is the housing that holds those parts and the ring gear. A kit alone does not replace a damaged carrier.
How do I find my axle's spline count?
Check the axle model and year, or count splines on the axle shaft end. Common counts include 27, 30 and 35 on Dana axles. Match the side gears to your shafts, and consult the manufacturer's data.
Can I use an open differential kit in a limited-slip unit?
Generally no. Kits listed for open differentials only are not designed for clutch-pack or other limited-slip designs. Choose a kit that states the type of differential it is meant for.
Can I install differential gears myself?
Experienced mechanics can, but the work requires proper setup tools, correct shims and a check of gear contact and backlash. If you lack experience, a drivetrain shop is a safer option.



