Dana 44 Complete Assemblies
Showing 37–38 of 38 resultsSorted by popularity
-
Dana 44 Complete Assemblies
G2 JK CORE 44 High Pinion Front Axle With 5.13 Ratio and 35 Spline ARB Air Locker Differential – C4JMFL513AP5
Dana 44 Complete AssembliesG2 JK CORE 44 High Pinion Front Axle With 5.13 Ratio and 35 Spline ARB Air Locker Differential – C4JMFL513AP5
- JK high pinion front axle with 5.13 ratio and ARB Air Locker
- New generation 8.8-inch JK 44 ring and pinion, 35 spline Placer axle shafts
- Built-in 3 degrees of extra caster for lifts of 6 inches and up
- G2 Axle and Gear part number C4JMFL513AP5, UPC 631410120479
SKU: G/2C4JMFL513AP5 -
Dana 44 Complete Assemblies
CORE 44 Front Axle Assembly with 4.10 Ratio and Eaton E-Locker
- Complete CORE 44 front axle housing with 4.10 ratio
- Eaton E-Locker, 30 spline G2 chromoly axles and SAE bearings
- Built for 1997-2006 Jeep Wrangler TJ and 1984-2001 Cherokee XJ
- G2 Axle and Gear UPC 631410132847
SKU: G/2C4TSFS410EC0
What a complete assembly is
A complete Dana 44 assembly is a fully built axle: housing, ring and pinion, carrier or differential, axle shafts, brackets and usually the cover. It saves the labor of building an axle from parts and setting up gears. Builders often use these when upgrading from a lighter factory axle on a Jeep, or when swapping a rear axle for a stronger design.
Choosing one
Start with the application. The sample products here are largely Jeep JK units, and they are sold front or rear. Housing brackets, spring perches, control arm mounts and track bar positions are vehicle-specific, so an assembly for one chassis will not bolt up to another without modification. Pick by position, intended lift height and tire size.
- Gear ratio: Taller tires call for numerically higher ratios, such as 4.88, 5.13 or 5.38, to bring back acceleration and keep the engine in its power band. The front and rear must match each other.
- Locker or limited slip: Options include air lockers, electric lockers and automatic lockers. Each has different control, cost and street manners.
- Spline count and axle shafts: More splines and larger shafts add strength but may need matching hubs and joints.
Specs to compare
Look at tube wall thickness, axle shaft material, the U-joint series, and whether the housing has extra caster built in for taller lifts. Check track width so the wheels sit where your fenders and wheel offset allow. Note whether the assembly includes brakes or a disc brake kit, and whether it is the standard or metric version where the listing says so. A replacement housing alone, as one listing here shows, is not the same as a complete axle.
Installation and compatibility
Swapping an axle is a major job that involves suspension, steering, brake lines, driveshafts and sometimes ABS sensors. Brake and steering systems are safety items, so professional installation and alignment are strongly recommended, along with torque to specification on every bolt. Fill with the gear oil the manufacturer specifies, and break in new gears carefully with gentle driving and an early fluid change.
You may need new drive shafts, a different track bar, and updated brake lines. Confirm fitment for your exact year, make, model and trim, and read the manufacturer's specifications. Verify that the axle's ratio matches the other axle and your tire size before ordering.
Planning a swap and common mistakes
Before buying, make a full plan. Check the width of the axle against your fender clearance and wheel offset, the bolt pattern of the hubs, and whether your wheels and brake rotors will carry over. Find out whether your steering linkage, track bar and drive shafts must change. Some builders also need a transmission or transfer case upgrade to take advantage of a stronger axle, though that is a separate decision.
Common mistakes include forgetting the cost of ancillary parts, mismatching gear ratios, and neglecting the pinion angle. Pinion angle should point the yoke toward the transfer case or transmission within the range that the drive shaft joints can handle. Skipping the alignment after a swap leads to uneven tire wear and poor handling.
After the swap, check fluid levels, torque on bolts and the gear mesh pattern if gears were adjusted. Change the gear oil after the first few hundred miles to remove break-in wear metal. Listen for whine or clunks, and check axle breather lines so they are routed up high.
Popular Dana 44 Complete Assemblies brands
Dana 44 Complete Assemblies FAQ
Why must front and rear gear ratios match?
Both axles must turn at the same relative speed in four-wheel drive. Mismatched ratios cause binding and driveline wear. When regearing or swapping an axle, use the same ratio at both ends.
What gear ratio should I choose for bigger tires?
Larger tires lower the effective ratio, so a numerically higher ratio helps restore performance. The right number depends on tire size, engine and transmission. Gear ratio calculators and the manufacturer's recommendations can guide you.
Is a Dana 44 complete assembly a bolt-in swap?
Usually not fully. Brackets are chassis-specific, and you may need drive shafts, brake lines or alignment work. Check what the listing covers and have the swap done carefully, preferably by a professional.
What is the difference between air and electric lockers?
Both lock the differential on command. Air lockers use an onboard compressor and air line, while electric lockers use a wiring and switch. Each has its own installation needs, so check what comes with the axle.
