Select your vehicle

G2 Ford 9 Inch Minor Ring and Pinion Installation Kit – 25-2011

G2 Axle and Gear

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • For the Ford 9 inch rear axle
  • Minor kit: bearings are not included
  • Shims, crush sleeve, pinion nut and pinion seal
  • Part number 25-2011

Description

Overview

The G2 Axle and Gear 25-2011 is a minor ring and pinion installation kit for the Ford 9 Inches rear axle.

The Ford 9 inch is a common swap-meet axle, and the 25-2011 supplies the small parts to set its gears. It holds a shim kit, pinion nut, crush sleeve, pinion seal, ring gear bolts, silicone sealer, Loctite and marking compound.

Ford’s 9 inch axle is popular with builders, and G2’s 25-2011 serves gear installs on it without bearings. The kit supplies the shim kit for depth, a pinion nut, crush sleeve and seal, new ring gear bolts, silicone sealer, Loctite and gear marking compound. Installers who also want bearings would pair this work with parts bought separately. Pairing it with a matching Ford 9 inch gear set completes the job.

Key features

  • Minor kit for the Ford 9 Inches axle (rear)
  • Meant for jobs that keep the existing bearings
  • Shim kit for setting pinion depth and carrier position
  • Pinion nut, crush sleeve and pinion seal
  • Ring gear bolts and silicone sealer
  • Loctite and gear marking compound

Setting pinion depth

Pinion depth and carrier position decide how the ring and pinion teeth mesh, and small shim changes shift the contact pattern noticeably. Measure the old setup and mark the existing shims before pulling anything apart, so you know where you started. Setting the carrier bearing preload and the pinion crush correctly matters as much as the gear mesh itself.

Gear marking compound is applied to the ring gear teeth to show the contact area after a few turns of the pinion. Adjust shims in small steps and retest until the pattern sits centered and well formed. Silicone sealer and thread locker should be used only where the instructions call for them, since too much can squeeze into the bearings.

  • Mark existing shims before disassembly
  • Replace the pinion nut and seal
  • Use a torque wrench on the pinion nut
  • Retest the gear pattern after each shim change

Specifications

Brand G2 Axle and Gear
Part number 25-2011
UPC 631410094855
Kit type Minor kit
Axle location Rear
Axle type Ford 9 Inches
Axle manufacturer Ford
Manufacturer part number G/225-2011

Vehicle fitment

It is a minor kit for the rear Ford 9 Inches axle. Confirm your axle type and year before ordering.

Confirm your vehicle’s axle type and year before ordering.

Installation notes

A Ford 9 inch third member is removable, which makes bench setup practical. Use the shims for pinion depth and the compound to check the pattern.

Before starting the 25-2011 job on the Ford 9 Inches axle, gather a dial indicator, a torque wrench and clean gear oil. Note the old pattern on the teeth, because the shims in the 25-2011 are the means of correcting the new one. The old nut and seal are replaced. Keep races paired with bearings.

What’s included

  • Proper shim kit
  • Pinion nut
  • Crush sleeve
  • Pinion seal
  • Ring gear bolts
  • Silicone sealer
  • Loctite thread locker
  • Gear marking compound

Not included: bearings and gears; the 25-2011 is a minor kit for the Ford 9 Inches axle.

SKU: G/225-2011 Category:

Specification

Shipping weight 3.00 lbs
Package dimensions 12.90 × 12.80 × 3.10 in
brands

Questions & Answers

What axle does the 25-2011 kit fit?

It fits the rear Ford 9 inch axle. Confirm your axle type and year before ordering, since this kit is designed only for that axle.

What is included in the 25-2011 kit?

Included are a proper shim kit, pinion nut, crush sleeve, pinion seal, ring gear bolts, silicone sealer, Loctite and gear marking compound.

Does the 25-2011 include bearings or gears?

No, bearings are left out of this minor kit. The part number to look for is 25-2011. That applies to the Ford 9 Inches rear axle.

How can I tell the gear pattern is right?

The contact pattern should sit centered on the ring gear teeth with even marks on both drive and coast sides. A pattern that runs to the tip or root of the teeth needs shim adjustment. Recheck the pattern after the new gears have been run in.

Do I need to replace the bearings with this kit?

Not with this minor kit, since it is built for jobs that keep the existing bearings. Inspect the bearings for pitting, roughness or play before reassembly. Replace any worn bearing or race before setting the new gear pattern.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon