Overview
The Baer Brakes Big Claw 2302023 is a pair of rear disc brake rotors for GM 1500 trucks from 1999 to 2018 and GM 1500 SUVs from 2007 to 2018, sold as a set. They are one-piece, full cast iron rotors with curved directional vanes that Baer says improve cooling.
Baer offers these as larger than stock rotors, up to 2 inches larger on some applications, and pairs them with new caliper relocation brackets so the calipers sit outward while OE pads and hardware still work. Baer also points to outside testing that measured up to a 49 percent gain in braking effectiveness from the larger diameter.
Key features
- 14 inch outside diameter rotors with curved vanes
- Cross-drilled and slotted friction surface for venting dust and gases
- Purpose-cast one-piece directional vane design
- Zinc-plated finish against rust and corrosion
- Six-hole mounting pattern on a 5.5 inch bolt circle
- Bolts on directly with no brake bleeding required
- Floating design
Rear rotor wear and replacement
Rear rotors wear down each time the pads clamp them, so their thickness drops over time. Service minimums matter because a thin rotor can overheat, crack or lose clamping performance. Check thickness, surface and runout at each pad change, and replace rotors that show deep scoring, heat checks or a noticeable lip at the outer edge.
The rotor is only part of the rear brake setup. Hub faces need to be clean and flat, lug bolts should be snug and evenly tightened, and caliper slide pins need to move freely. Corrosion on the hub or a rusted slide pin can cause pulsation even on a new rotor. Clean the mating surfaces before installing and check that the relocation brackets seat correctly.
- Clean rust from the hub face before mounting
- Re-torque lugs after the first few drives
- Replace pads in sets on the same axle
Specifications
| Brand | Baer Brakes |
|---|---|
| Part number | 2302023 |
| UPC | 844165004141 |
| Sold as | Set |
| Axle | Rear |
| Drive | 2WD, 4WD |
| Construction | One piece, full cast |
| Material | Cast iron |
| Outside diameter | 14 inch |
| Inside diameter | 8.268 inch |
| Center hole diameter | 3.095 inch |
| Nominal thickness | 0.799 inch |
| Discard thickness | 0.72 inch |
| Overall height | 3.366 inch |
| Mounting bolt hole circle | 5.5 inch |
| Mounting bolt hole diameter | 0.65 inch |
| Mounting bolt holes | 6 |
| Surface type | Slotted x drilled |
| Vent design | Curved |
| Finish | Zinc plated |
| Floating | Yes |
| ABS tone ring included | No |
| Warranty | Limited 1 year |
| Country of origin | US |
Vehicle fitment
The manufacturer fitment list covers 2007–2017 Cadillac Escalade; 1999–2004 and 2009–2017 Chevrolet Silverado 1500; 2007–2014 Chevrolet Suburban 1500; 2001–2017 Chevrolet Tahoe; 1999–2004 and 2007–2017 GMC Sierra 1500; and 2007–2017 GMC Yukon. Trims include Hybrid, LS, LT, LTZ, SLE, SLT, Denali and Z71 depending on the model.
Silverado 1500 fits model years 1999–2004 and 2009–2017, and Sierra 1500 fits 1999–2004 and 2007–2017. Confirm fit for your vehicle’s year, model and trim before ordering.
Installation notes
Baer says these rotors bolt on directly and need no brake bleeding. Wheel clearance is not guaranteed across all wheel designs, so use the template and test-fit the wheel and spare before mounting. The relocation brackets change caliper position, so check pad and hardware clearance after installation.
What’s included
It bolts on directly and needs no brake bleeding. Test-fit the wheel and spare with the template before mounting, since wheel clearance varies by design. Check pad and hardware clearance after installing the relocation brackets.

















