Overview
The Baer Brakes ReMaster 6805211 is a master cylinder and proportioning valve kit with a 1-1/8 inch bore, gray billet body and left-side ports. It combines a machined master cylinder, an adjustable proportioning valve for front-to-rear brake balance, and pre-bent hardlines with 3/8 inch inverted flare fittings in one package. Confirm fit for your vehicle’s year, model and trim before ordering.
The master cylinder body and caps are fully machined from 6061 T6 billet aluminum. The caps are knurled and screw on for filling. The proportioning valve sits on an integrated mounting block designed to install beneath the ReMaster master cylinder, and it is adjusted with a knob. A proportioning valve controls how much pressure reaches the rear brakes compared with the front, which matters when brake components or vehicle weight change.
Key features
- Fully machined 6061 T6 billet aluminum master cylinder with gray body
- Adjustable proportioning valve with knob control and gray anodized finish
- Integrated mounting block for the valve, with gray anodized finish
- Knurled screw-on caps that make filling easier
- Dual integral reservoir with removable seats
- Two master cylinder outlets with 3/8-24 inch ports
- Pre-bent 3/16 inch hardlines with inverted flare fittings
- Made in the USA
Choosing a proportioning setup
A proportioning valve limits how much pressure reaches the rear brakes compared with the front. When brake components, tire size or vehicle weight change, the front-to-rear balance can shift, so the knob setting is worth rechecking after any upgrade. Because this kit pairs a master cylinder with a valve on a shared block, the two parts are usually matched as a set rather than mixed with other hydraulics.
Before changing the layout, measure the existing bore, reservoir clearance and line routing. Check the fluid level at the reservoir during installation, and bleed the system completely after any line work. Moving the valve to a new position can change pedal feel, so test the brakes at low speed in a clear area before normal driving.
- Recheck the knob setting after pad or rotor changes
- Inspect hardlines for chafing near moving parts
- Replace flare fittings that show seepage or thread damage
Specifications
| Brand | Baer Brakes |
|---|---|
| Part number | 6805211 |
| UPC | 90127856147 |
| Series | ReMaster |
| Kit contents | 1 master cylinder assembly, 1 proportioning valve |
| Bore size | 1-1/8 inch (1.125) |
| Master cylinder material | 6061 T6 billet aluminum |
| Finish | Gray body, black anodized caps and lid |
| Port exit | Left side |
| Master cylinder outlet ports | 2 ports, 3/8-24 inch |
| Proportioning valve type | Adjustable, knob |
| Proportioning inlet and outlet | 3/8-24 inch |
| Reservoir | Dual, integral style |
| Hardlines | 3/16 inch pre-bent |
| Fittings | Banjo (no brass seat) and 3/16 inch inverted flare tube nuts with brass seat |
| Mounting holes | 2 |
| Removable seats | Yes |
| Warning light connector | No |
| Country of origin | USA |
Vehicle fitment
The firewall mounting bracket uses a 2-bolt GM/Ford style and is not included, so compare it with your firewall before buying. Confirm bore size and port location against your current hydraulic layout.
Bore size and port side are the two details to check against your existing setup before ordering. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
Test-fit the pre-bent lines to the valve and master cylinder before final tightening. Bleeder screws and bleeder hoses are not included, so have them on hand before bleeding. After bleeding, check each fitting for leaks while the pedal is held under pressure.
What’s included
One master cylinder assembly with cap, one adjustable proportioning valve with integrated mounting block hardware, 3/16 inch pre-bent hardlines and the listed fittings.
Not included: firewall mounting bracket, mounting hardware, bleeder screws, bleeder hoses, brake booster, brake pressure switch, sensor, and gasket or seal.

















