Switch Pods
Showing 37–48 of 76 resultsSorted by popularity
-
Switch Pods
SPOD 6 Switch sPOD – 620-0915
- Fits 2009 to 2016 JK Wrangler, Rubicon and Unlimited, 2 and 4-door models
- Six switch sPOD with a 12 position terminal block for accessories
- 8 gauge power leads with crimped and soldered battery terminal
- Six ATO fuses supplied: three 15 amp and three 30 amp
- Aeroforce gauge not included
SKU: POD620-0915 -
Switch Pods
SPOD 2009-2015 JK Wrangler 6 Switch System with Air Gauge – 610-0915
- Six-switch power block for 2009–2015 Jeep Wrangler JK, sold with an air gauge
- Six plug-in 40 amp relays and six fuses, with 15 and 30 amp ratings
- Integrated low-voltage cutoff at 10.6 VDC, back on at 12.4 VDC
- Two red, two amber and two green switches included
- SPOD part 610-0915, UPC 700007185471
SKU: POD610-0915 -
Switch Pods
SPOD 2007-2008 JK Wrangler 6 Switch System with Air Gauge – 610-07
- Six-switch power block with air gauge for 2007–2008 Jeep Wrangler JK
- Air gauge rated 0–200 psi with Camozzi quick-release fittings
- Six 40 amp plug-in relays, six fuses and a 50 amp breaker
- Low-voltage cutoff at 10.6 VDC, back on at 12.4 VDC
- SPOD part 610-07, UPC 700006892111
SKU: POD610-07 -
Switch Pods
2009 – 2017 JK model 6 Switch System & Source System with Blue Switches
- Designed for the 2009-2017 Jeep Wrangler JK
- Complete plug and play sPOD and Source power distribution, pre-wired
- Fused and relayed for adding accessories, with six blue switches
- Integrated low-voltage cut-off (LVCO) protects starting voltage
- Part number 600-0915LT-LEDB
SKU: POD600-0915LT-LEDB -
-
Switch Pods
SPOD 2007-2008 JK Wrangler 6 Switch System – 600-07
- Six-switch power distribution kit for 2007–2008 Jeep Wrangler JK
- Six plug-in 40 amp relays and six fused outputs
- Low-voltage cutoff at 10.6 VDC with cut-back at 12.4 VDC
- Two red, two amber and two green switches included
- SPOD part 600-07, UPC 700006892080
SKU: POD600-07 -
Switch Pods
SPOD 1997-2002 TJ Wrangler 6 Switch System with Air Gauge – 510-97
- Six-switch power block with air gauge kit for 1997–2002 Jeep Wrangler TJ
- Air gauge rated 0–200 psi with Camozzi quick-release fittings
- Six 40 amp plug-in relays and six fuses
- Low-voltage cutoff at 10.6 VDC, back on at 12.4 VDC
- SPOD part 510-97, UPC 700006892221
SKU: POD510-97 -
Switch Pods
SPOD 1997-2002 TJ Wrangler 6 Switch System – 500-97
- Six-switch power block for 1997–2002 Jeep Wrangler TJ
- Six plug-in 40 amp relays with fused accessory outputs
- Low-voltage cutoff at 10.6 VDC, back on at 12.4 VDC
- Two red, two amber and two green switches included
- SPOD part 500-97, UPC 700006892201
SKU: POD500-97 -
Switch Pods
SPOD 2003-2006 TJ/LJ Wrangler 6 Switch System – 500-03
- Six-switch power distribution kit for 2003–2006 Jeep Wrangler TJ and LJ
- Six 40 amp plug-in relays and six fuses, with 15 and 30 amp ratings
- Integrated low-voltage cutoff at 10.6 VDC, cut-back at 12.4 VDC
- Two red, two amber and two green switches included
- SPOD part 500-03, UPC 700006892219
SKU: POD500-03 -
-
-
Switch Pods
Daystar A-Pillar Switch Pod with Rocker Switches – KJ71056BK
- A-pillar switch pod for the 2007–2018 Jeep Wrangler JK
- Includes four 20-amp, 3-pole rocker switches in blue, green, amber and red
- Direct replacement for the factory A-pillar, easy install
- Daystar part KJ71056BK, UPC 618089005191
SKU: DAYKJ71056BK
What a switch pod does
Off-road builds add many electrical accessories: light bars, rock lights, air compressors, winches and cameras. A switch pod puts the controls in one panel, usually near the driver, and ties them to a relay-based control unit under the hood or dash. This keeps current-carrying wires away from the cabin and reduces the clutter of individual switches added in random places.
Types of systems
- Vehicle-specific kits are shaped to fit the dash or console of particular models, such as a Wrangler TJ or a Tacoma. They often use factory mounting points for a clean look.
- Universal panels and bezels mount in a bracket, roll bar or console, and suit custom builds.
- Control systems use a power module that handles the high-current switching. Some are driven by a touchscreen or a small switch panel.
- Harnesses and accessories include extension wiring, battery cables and mounts for tablets or screens.
What to compare
- Number of switches: count the accessories you run now, then add a few spare circuits for future upgrades.
- Current rating: every circuit and the main feed have a maximum amperage. Add up what you will connect and stay below the rating.
- Switch type: rocker, toggle, momentary or programmable. Momentary functions suit horns and winch-style actions.
- Environmental protection: consider whether the control module is sealed against moisture if it will be under the hood.
- Illumination: backlit switches help at night, but check that the brightness is adjustable.
Installation notes
Disconnect the battery before starting work. Use properly sized wire for the load, a fuse or breaker near the battery, and weatherproof connectors where wires pass through the firewall. Route wiring away from heat and moving parts, and use grommets to protect it at pass-throughs. Test each circuit before closing up the dash. Systems that connect to a vehicle's factory harness should be confirmed against the wiring information for your exact year, make and model. If wiring is unfamiliar, have an automotive electrician perform the installation.
Labeling and upkeep
Label each switch clearly, since a panel full of identical rockers is easy to misread in the dark. Periodically check connectors for corrosion, confirm that fuses are the right rating and keep a spare set of fuses in the vehicle.
Planning and common mistakes
Before buying a system, make a list of every accessory you expect to run now and in the future. Write down the amperage of each, since that determines wire size, fuse size and the control unit's capacity. Pods are easier to install when you choose a mounting location first. Consider whether the driver can reach the switches comfortably without taking eyes from the road, and whether passengers or seat belts could accidentally hit them.
- Do not share one circuit between large loads. A pair of light bars and a compressor should not run off the same fused lead.
- Do not skip the main fuse. Place a fuse or breaker near the battery on the feed wire, because a short anywhere along the run could otherwise ignite insulation.
- Do not rely on tape. Use heat-shrink connectors or sealed terminals, particularly in the engine bay.
- Keep ignition-switched and constant power separate if you do not want accessories draining the battery when parked.
Popular Switch Pods brands
- SPOD (40)
- Rugged Ridge (16)
- Daystar (8)
- Advanced Accessory Concepts (8)
- Painless Wiring (8)
- ARB 4x4 Accessories (6)
Switch Pods FAQ
Do I need a switch pod to run off-road lights?
No, individual switches and relays work too. A switch pod simply organizes controls in one place and often includes the relays and fusing, which can make wiring cleaner and easier to expand later.
Can a switch pod handle an air compressor or winch?
Only if the circuit rating supports the draw. Compressors and winches pull high current, so check the amp rating of the module and wiring, and consider wiring them directly through a dedicated relay and breaker.
Will a vehicle-specific pod fit my dash?
Vehicle-specific kits are shaped for particular models and years, and dash designs change. Confirm the listed fitment for your exact year, make and model before choosing a part number.
Is installation difficult?
Basic kits need simple hand tools, a fuse and clean wiring. The main risks are undersized wire, poor connections and missing fuses. If you are unsure about automotive wiring, use a qualified installer.











