Overview
The Baer Brakes 6801330RP is a polished ReMaster master cylinder with a 1.125 inch (1-1/8) bore and right side ports, designed for the 1999-2004 Ford Mustang Cobra hydroboost setup. Its two bolt flange is built for the SN95 hydroboost firewall bracket, so it is not offered as a universal cylinder.
The body is a single piece of 6061 T6 billet aluminum, and its top is held down by six allen screws. The two outlet ports take either inverted flare fittings with removable brass seats or banjo style fittings. Knurled, screw-on caps make filling the dual reservoirs easier without spillage.
Key features
- Two bolt flange for the 1999-04 SN95 Mustang hydroboost firewall bracket
- Fully machined 6061 T6 billet aluminum construction
- Right side port exit with two 3/8-24 outlets
- Outlets accept inverted flare (removable brass seats) or banjo fittings
- Knurled, screw-on caps for filling without spillage
- Polished body, caps and lid
Bleeding and fluid level
A master cylinder on a hydroboost system works with the booster, so air or low fluid can show up as a soft or uneven pedal. Bleed the system in the order the brake layout requires, and keep the reservoir topped up during the process so air is not pulled into the lines. Fresh fluid from a sealed container helps keep moisture out of the circuit.
Inspect the cylinder and lines after installation for seepage at the outlet fittings and around the caps. Brake fluid absorbs moisture over time, so flushing the system on a regular service schedule helps keep the cylinder seals in better condition. Replace the cylinder if it leaks past the seals or the pedal sinks under steady pressure.
- Bleed in the sequence your brake layout requires
- Keep the reservoir filled during bleeding
- Use fresh fluid from a sealed container
Specifications
| Brand | Baer Brakes |
|---|---|
| Part number | 6801330RP |
| UPC | 844165054290 |
| Series | ReMaster |
| Bore size | 1.125 inch (1-1/8) |
| Material | 6061 T6 billet aluminum |
| Body finish | Polished |
| Caps and lid finish | Polished |
| Port exit | Right side |
| Outlet ports | 2 at 3/8-24 |
| Outlet fittings | Banjo without brass seat; 3/16 inch inverted flare with tube nuts and brass seat |
| Reservoir | Dual, integral, 7oz per reservoir; fill to 75 percent or 5.25oz per reservoir |
| Flange | 2 bolt, 1999-04 SN95 Mustang hydroboost specific |
| Stroke | 1.3 |
| Area | 0.97 |
| Volume ratio | 0.0840277777777778 |
| Country of origin | USA |
Vehicle fitment
Baer Brakes ties this cylinder to the 1999-2004 Ford Mustang Cobra with hydroboost, and the flange is made for the 1999-04 SN95 hydroboost. No structured fitment list is attached, so match the model year and hydroboost setup first.
The SN95 flange is specific to 1999-04 Mustangs, so it does not cover other Mustang years or systems without that hydroboost bracket. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
Mount the cylinder to the SN95 hydroboost firewall bracket, then pick one fitting style per outlet. Banjo fittings take no brass seat, while inverted flares use the removable seats and tube nuts supplied with the cylinder. Route lines with the right side port exit in mind before you tighten anything, and fill the reservoirs only to the 75 percent level.
What’s included
One ReMaster master cylinder assembly with reservoir and cap, two brass seats and two tube nuts.
Not included: the booster itself, mounting hardware, the bleeder screw and bleeder hoses, and the brake pressure switch.













