Clutch Parts
Clutch Parts covers the mechanical and hydraulic pieces that let a manual transmission Jeep shift: release bearings, clutch master and slave cylinders, pedal rods, bellcrank levers and flywheels, mostly from Crown Automotive and Omix-Ada with a few Centerforce and Rugged Ridge items. Applications run from the 1946 Willys CJ through the CJ5, CJ7 and Scrambler to the Cherokee XJ, Comanche and Wrangler YJ, TJ and JK.Use the subcategories to narrow by model family, then compare the products below.

A slipping clutch, a pedal that sinks to the floor or a fork that clunks on the bellhousing can leave a manual-transmission Jeep stuck at the trailhead. These factory-style clutch parts cover the kit itself plus the linkage, hydraulics and small hardware that make the pedal work.
Most parts here suit CJ-era Jeeps and their mechanical bellcrank linkage: pedal rods, bellcranks, bushings, clips, boots, adjusters and return springs. Later Jeeps with hydraulic clutches are covered too, with master and slave cylinders, hose assemblies and a hydraulic release bearing. A few parts serve full-size SJ trucks and the XJ Cherokee. Alignment tools, forks and a flywheel round out a full clutch job.
Shop clutch parts by vehicle
Popular clutch parts
-
-
-
Clutch Parts
Crown Automotive Hydraulic Clutch Tube and Hose Assembly – 53004164
- Hydraulic clutch tube and hose assembly for 2.5L engines, Crown Automotive part 53004164
- Runs from clutch master cylinder to slave cylinder
- Fits 1980–1983 Jeep CJ5 and CJ7 and 1981–1983 Scrambler
- UPC 70000693882
SKU: CRO53004164 -
-
XJ Cherokee Clutch Parts
Crown Automotive Clutch Hose Retaining Pin – 83503385
- Clutch hose retaining pin, Crown Automotive part number 83503385
- Fits 1991–1993 Jeep Cherokee XJ, 1991–1992 Comanche and 1991–1993 Wrangler YJ
- Fitment is listed by the manufacturer; no other details are given
SKU: CRO83503385
Clutch parts reference
Details from the listed clutch parts, grouped by system. Engine and transmission matter as much as the model, so match both before ordering.
Linkage types
| Mechanical | Hydraulic | |
|---|---|---|
| Pedal connects through | Rods and a bellcrank | Master and slave cylinder |
| Common wear items | Bushings, clips, boots, rods | Seals, hoses, release bearing |
| Adjustment | Rod adjuster sets free play | Self-adjusting |
| Listed here for | CJ and full-size SJ | Later Jeeps, AX15 and BA 10/5 |
Release bearings by engine
| Omix-ADA 16906.02 | GM 2.5L, 4.2L 258, 304 and 360 V8, 2.1 diesel |
|---|---|
| Omix-ADA 16906.05 | AMC 232–258 six, 304–401 V8 |
| Omix-ADA 16906.06 | 2.8L and 3.8L engines |
| Crown 83503383 hydraulic | BA 10/5 transmission |
Clutch job checklist
- Replace the disc, pressure plate and release bearing together
- Fit a new pilot bearing or bushing in the crankshaft
- Inspect the flywheel for heat spots and cracks; resurface or replace
- Center the disc with an alignment tool that matches the input spline
- Check the fork, pivot stud and boots for wear while the bellhousing is open
- Bleed a hydraulic system, or set free play on a mechanical linkage
CJ bellcrank linkage parts
| Bellcrank (Crown J0911467) | 8-1/8" long, 5-3/4" between brackets |
|---|---|
| Bellcrank lever (16919.07, J5364621) | Connects pedal to fork |
| Bellcrank bushing (J3167067) | Plastic, 2 needed |
| Bellcrank bushing clip (J3169769) | 2 required |
| Pivot repair kit (3167067K) | Bushings, clips and boots |
| Release rod (J8126668) | Bellcrank to fork, with adjuster nut |
| Clutch rod (J5364620) | Pedal to bellcrank, 0–1" body lift |
| Bracket and pivot (J5355339) | Mounts to firewall, with pivot stud |
Hydraulic system parts
| Master cylinder (4636864, 16908.07) | 4 and 6 cylinder engines |
|---|---|
| Slave cylinder (52107640S) | AX15 transmission |
| Tube and hose (53004164) | 2.5L, master to slave cylinder |
| Tube and hose (52060477AE) | 2- and 4-door, left-hand drive |
| Master cylinder actuator (5106043AB) | Left-hand drive only |
| Hose retaining pin (83503385) | XJ Cherokee |
Clutch parts change with engine, transmission and year. Check the engine size and transmission model listed on each part, and confirm by part number when replacing a factory piece.
All Clutch Parts 90 parts
What is in a clutch system
A manual Jeep uses the same basic chain of parts regardless of age. The pedal moves a rod or pushes a master cylinder; a linkage or hydraulic line transfers that motion to the release fork; the fork pushes a release bearing, also called a throwout bearing, against the pressure plate fingers; and the pressure plate lets go of the disc so the flywheel can spin free of the transmission. This category holds the parts around the clutch itself. The pressure plate and disc kits live in the separate Clutch category under Drivetrain.
Early CJs use a purely mechanical linkage: a pedal rod, a bellcrank, also called a Z-bar, that pivots between the frame and the engine, and a clutch fork rod. From the mid 1980s Jeep moved to hydraulics, with a master cylinder at the firewall and a slave cylinder either external on the bellhousing or, on the AX15 and BA 10/5 transmissions, a concentric unit that combines the slave cylinder and bearing in one piece inside the bellhousing.
Diagnosing before you buy
- A squeal or growl with the pedal depressed that goes away when you lift your foot usually points to the release bearing.
- A pedal that sinks to the floor or needs pumping, with no external leak, is typically a failing master cylinder. Fluid dripping behind the bellhousing points to the slave cylinder.
- Sloppy engagement on a CJ with mechanical linkage is often worn bellcrank bushings or a bent pedal rod, not the clutch itself.
- Chatter, a shudder on takeoff, can be a heat-checked or warped flywheel, oil contamination of the disc, or loose engine mounts.
Identifying the right part
Jeep used several transmissions and engines within a single body code, and the clutch parts changed with them. A release bearing for the 2.5L four cylinder differs from the one for the 4.0L six, and both differ from the AMC V8 parts in a 1970s CJ. Confirm the transmission, for example AX5, AX15, BA 10/5, T4, T5 or T176, and the engine before choosing. The transmission tag or casting numbers settle arguments that the title alone cannot.
Hydraulic parts bring their own gotchas. Some master cylinders come with the hose and reservoir, others are bare. A concentric slave cylinder for the AX15 replaces the bearing and cylinder together, so do not buy both. On a 1987 to 1990 XJ, check whether your hydraulic line uses the early quick-connect fitting, which can only be separated with the right tool.
Installation notes
Replacing a release bearing or slave cylinder means pulling the transmission, so replace the whole set at once: bearing, pilot bearing, disc and pressure plate, and resurface or replace the flywheel if it shows heat spots or scoring. Flywheel bolts are usually one-use items on newer Jeeps and should be torqued to the factory figure in sequence. Lightly grease the input shaft splines and the fork pivot, but keep grease off the disc and flywheel face.
Hydraulic systems need a thorough bleed after any opening of the line. Many Jeep setups do not bleed well with the pedal alone; bench bleeding the master cylinder first, or using a vacuum or pressure bleeder at the slave, saves a lot of frustration. Use fresh DOT 3 fluid from a sealed container, since absorbed moisture lowers the boiling point and corrodes the bores.
Mechanical linkage on CJs
On a 1972 to 1986 CJ, the bellcrank rides on two bushings and a pair of ball studs, one on the frame and one on the engine block. These wear oval, and worn bushings let the lever rock instead of pivoting, which eats pedal travel. A new bellcrank lever is often sold without bushings and clips, so check what the kit includes and order the bushing set at the same time. Adjust free play at the fork rod after assembly so the bearing is not riding on the fingers at rest.
Popular Clutch Parts brands
Clutch Parts FAQ
What is the difference between a release bearing and a throwout bearing?
They are the same part under two names. The bearing sits on the transmission input shaft sleeve and is pushed by the clutch fork against the pressure plate fingers when you press the pedal. Replace it whenever the transmission is out for clutch work.
Why does my Jeep clutch pedal go to the floor with no leak?
A master cylinder can fail internally, letting fluid bypass the piston seals without dripping outside. The pedal sinks or needs pumping. Check the reservoir and the firewall behind the pedal for seepage, and inspect the slave cylinder too before replacing parts.
Do I need to replace the flywheel when changing clutch parts?
Inspect it first. Light glazing can be machined away, but heat checking, deep scoring, cracks or a warped face call for replacement. A flywheel assembly for a 2.5L or 4.0L Jeep is a direct fit, and new bolts should be torqued in sequence to the factory spec.
How do I bleed a Jeep hydraulic clutch?
Fill the reservoir with fresh DOT 3 fluid, bench bleed the master cylinder if it is new, then bleed at the slave cylinder with a helper on the pedal or a vacuum bleeder. Keep the reservoir topped up throughout. Some concentric slave cylinders bleed easier with the line disconnected and held high.




















