Switches
Showing 25–35 of 35 resultsSorted by popularity
-
Switches
Oracle Lighting Pre-Wired On/Off Flush Mount LED Switch (Red) 2012-003
- Oracle Lighting 2012-003 red pre-wired flush mount LED on/off switch
- Needs a 16MM mounting hole; 12-volt
- Glowing red power ring when activated
- Universal fit, not matched to a vehicle
- Heavy-duty brass assembly with nickel plate finish
SKU: ORC2012-003 -
-
Switches
Oracle Lighting Pre-Wired On/Off Flush Mount LED Switch (Amber) – 2012-005
- Oracle Lighting 2012-005 amber pre-wired flush mount LED on/off switch
- Needs a 16MM mounting hole; 12-volt
- Amber / orange glowing power ring
- Universal fit with no year, make or model attached
- Heavy-duty brass assembly, nickel plate finish
SKU: ORC2012-005 -
Switches
Oracle Lighting Pre-Wired On/Off Flush Mount LED Switch (Green) – 2012-004
- Oracle Lighting 2012-004 green pre-wired flush mount LED on/off switch
- Needs a 16MM mounting hole; 12-volt
- Glowing green power ring when activated
- Universal fit with no vehicles matched to it
- Heavy-duty brass assembly with nickel plate finish
SKU: ORC2012-004 -
Switches
Oracle Lighting Pre-Wired On/Off Flush Mount LED Switch (Blue) – 2012-002
- Oracle Lighting 2012-002 blue pre-wired flush mount LED on/off switch
- Needs a 16MM mounting hole; 12-volt
- Glowing power ring when activated
- Universal fit; no specific vehicle assigned
- Heavy-duty brass assembly with nickel plate finish
SKU: ORC2012-002 -
Switches
Oracle Lighting Pre-Wired On/Off Flush Mount LED Switch (UV/Purple) – 2012-007
- Oracle Lighting 2012-007 pre-wired on/off flush mount LED switch
- UV/Purple illumination, 12-volts, push button
- Requires a 16MM mounting hole
- Heavy-duty brass assembly with nickel plate finish
- Universal fit; not waterproof; UPC 201200720143
SKU: ORC2012-007
Switch types you will find
Accessory switches control lights, air compressors, winches, fans, USB outlets and other 12-volt gear. Rocker switches are the most common and fit the factory dash panel on many vehicles. Toggle switches have a lever and are favored for rugged panels, including military-spec designs. Flush-mount round LED switches fit a drilled hole and often glow when on, while specialized parts include window switches, USB combos and kits for electric fans.
Ratings and wiring
Check the amp rating and voltage on the switch against the load. A switch rated for 20 amps at 12 volts handles a typical lighting circuit, but many high-draw accessories such as winches and compressors require a relay, with the switch handling only the low-current control signal. Use a fuse or breaker sized for the wire, located near the power source. Undersized wire or a switch pushed beyond its rating can overheat.
- Poles and throws: a 3-pole rocker usually has power, ground for the indicator light, and load terminals.
- Illumination: lit switches can help in the dark, but confirm the indicator wiring.
- Momentary versus latching: momentary switches return to center, useful for horns or winch control.
Mounting and sealing
Dash panels vary, so match the switch body to the hole shape, such as a standard rocker cutout or a 16 mm round hole as noted for some flush-mount types. Consider whether the switch is splash resistant if mounted in an exposed location, such as a roll bar panel or a bumper, since water and dust shorten contact life.
Installation notes
Disconnect the negative battery cable before wiring. Use proper terminals, heat-shrink or sealed connectors, and clean grounds, and label wires so later troubleshooting is simpler. Keep wiring away from sharp edges and heat sources. Switches with factory-style connectors or labeled covers, such as lighting symbols, are made for specific panels, so confirm fitment for your exact year, make and model.
Consider where the switches will live. A dedicated panel keeps wiring tidy, and labels on each switch prevent mistakes at night. Test every circuit with the vehicle running, and check the connections again after the first trail outing.
Materials, construction and common pairings
Quality switches have silver or gold-flashed contacts and a body rated for the stated current, with heavy-duty brass or nickel-plated terminals resisting corrosion. Cheap switches may use thin contacts that heat up and fail under load. Look for a rating stated in amps and volts, and for sealed designs where moisture is a concern. Metal toggles with rubber boots suit exposed locations.
Switches pair naturally with relays, fuse blocks, wire loom and connectors. For lighting, a relay harness sized for the lamp wattage protects the switch. For compressors, use the maker's recommended wire gauge and fuse. Electric fan kits include a thermostat or manual switch to override the temperature control, and a lit switch indicates when the fan is forced on. Switch panels let you gather several controls in one place, including USB ports and rocker switches.
Mistakes to avoid
Do not tap power from an unfused wire, and do not use thin wire for high loads. Do not forget a ground, since indicator lights fail without it. Use grommets where wires pass through metal, and avoid cutting into the factory harness.
Popular Switches brands
- Rugged Ridge (14)
- Oracle Lighting (6)
- Daystar (4)
- Omix-Ada (4)
- Crown Automotive (3)
- Painless Wiring (2)
- ARB 4x4 Accessories (2)
- SPOD (2)
- Dorman (1)
- Hella (1)
- Flex-A-Lite (1)
Switches FAQ
Do I need a relay with a high-power accessory?
Often yes. Winches, compressors and large light bars can draw more current than a dash switch should carry, so the switch triggers a relay and the relay carries the load. Check the accessory's amp draw.
What does a 3-pole rocker switch mean?
It has three terminals, typically power in, load out, and a ground or illumination terminal for the indicator light. Wiring diagrams differ by switch, so read the instructions.
How do I choose the right amp rating?
Pick a switch rated above the circuit's maximum current, and use a fuse matched to the wire gauge. If the load exceeds the switch's rating, use a relay.
Can I mount a switch outside the cabin?
Only if it is rated for splash and dust. Standard dash switches can fail when exposed to water. Look for sealed designs and protect connections with sealed connectors or dielectric grease.










