Differential Pinion Seal
Showing 25–27 of 27 resultsSorted by popularity
What the pinion seal does
The pinion shaft drives the ring gear inside the differential, and its yoke or flange connects to the drive shaft. The pinion seal sits where that shaft exits the housing and holds in the gear oil. When it wears or hardens, oil weeps down the yoke, gets flung onto the underside, and the axle can run low on lubricant. A leak at the pinion is one of the most common axle seal problems on older Jeeps and trucks.
Finding the right seal
Start by identifying the axle: Dana 30, Dana 44, Dana 35, AMC Model 20 or another. The listings here label seals by axle model, and many specify position, front or rear, and sometimes whether the axle is the inner or outer seal on a unit with two, such as the Dana Super 30. Seal dimensions differ between axles, and some are specific to a model year range or production date.
- Outside and inside diameter: The seal must match both the housing bore and the pinion yoke surface.
- Single or paired seals: Some axles use an inner and outer seal.
- Seal with nut kit: Some sets include a pinion nut, which must be replaced on certain axles.
Signs of a failing seal
Look for oil around the yoke, wet dust on the drive shaft or axle, a gear oil smell, or an axle that needs topping off often. Whining can mean low fluid or wear. If the yoke surface is grooved where the seal rides, a new seal may not stop the leak, and the yoke or a speedy sleeve may also need replacement.
Installation notes
This job involves removing the drive shaft, the yoke nut and the yoke, and the pinion bearing preload must be preserved. On many axles, the pinion nut is crush-style or has a specific torque. Mark the nut and shaft position, count the threads or follow the manufacturer's procedure, and reinstall to the same preload. Setting preload wrongly can wreck bearings, so experience matters here. If you are unsure, have a mechanic do it.
Use a seal driver to seat the new seal evenly, apply a thin film of gear oil on the lip, and refill the axle to the proper level with the fluid grade in the manufacturer's specification. Confirm fitment for your exact year, make, model and axle, as well as the seal dimensions, before starting. Clean off the old oil and check again for leaks after a short drive.
Diagnosis, tools and common mistakes
Before replacing the seal, confirm the leak is coming from the pinion and not from the axle vent, a cover gasket, an axle shaft seal or a leaking transfer case output. Wipe the area clean, drive a short distance, and look again. Oil that is thrown outward in a radial pattern around the yoke points to the pinion seal. Check the axle breather as well, because a plugged vent builds pressure and pushes oil past seals.
Helpful tools include a seal puller, a seal driver of the correct size, a torque wrench, a yoke holder and calipers to measure the yoke journal. Inspect the yoke where the seal rides, and if it has a visible groove, use a repair sleeve or a new yoke. Clean the seal bore thoroughly before the new seal goes in.
Common mistakes include damaging the new seal lip by tapping it in crookedly, forgetting to replace a crush sleeve or a pinion nut that is meant for single use, and underfilling the axle with gear oil afterward. Take note of exactly how many times you turn the nut, and keep the drive shaft flange bolts tight when you reconnect them.
Popular Differential Pinion Seal brands
Differential Pinion Seal FAQ
How do I know which pinion seal my axle uses?
Identify the axle model, such as Dana 30 or Dana 44, then position and year. Some axles have both inner and outer seals. Check the listing's notes and compare dimensions to your housing and yoke.
Why is my pinion seal leaking?
Seals harden with age, wear against the yoke, or fail from a clogged axle vent, which builds pressure. A grooved yoke surface can also cause leaks. Inspect the yoke and vent when replacing the seal.
Do I need to reset pinion preload when replacing the seal?
Yes, the preload must be preserved. Many axles use a crush sleeve or a specific torque on the pinion nut. Follow the manufacturer's procedure or have a mechanic do it, since the wrong preload damages bearings.
Can I drive with a leaking pinion seal?
A small weep may be tolerable briefly, but low gear oil causes heat and gear wear. Check the level often and repair soon. Heavy leaks should be fixed right away.


