Select your vehicle
-13%

Pro Comp PRO-M Monotube Rear Shock Absorber – PR2082

Pro Comp Suspension

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Pro Comp PRO-M rear monotube shock, part PR2082, sold individually
  • Designed for 0 to 1 inch of lift
  • Extended 22.3 in, collapsed 14.2 in
  • Fits the 2000 to 2006 Toyota Tundra

Description

Overview

The Pro Comp Suspension PR2082 is a PRO-M rear monotube shock for the 2000 to 2006 Toyota Tundra, with 0 to 1 inch of lift. It has an extended length of 22.3 inches and a collapsed length of 14.2 inches, and it is sold individually.

The shock is nitrogen gas charged, with a floating piston and multi-stage disc pack valving. The wiper seal is designed to prevent leaks, and the 14 mm chrome hardened shaft is part of the build.

Key features

  • Rear monotube design for 0 to 1 inch of lift
  • Extended length 22.3 inches, collapsed length 14.2 inches
  • Nitrogen gas charged with floating piston
  • Multi-stage disc pack valving, vehicle specific
  • 14 mm chrome hardened shaft
  • Polyurethane shock boot included

Choosing a lift height

A narrow lift range means the shock works in a tight window, so small differences in ride height can change how the damper behaves. Measure the rear height of your Tundra before fitting, from the axle to the frame on both sides. Level readings matter more than a single number, since worn springs can sit lower on one side.

Leaf spring condition affects how the shock works, so inspect the springs and bushings during installation. Look for sagging, cracked leaves or worn hangers. A damper that is fresh but paired with tired springs will feel loose and may not perform as expected. Test movement by hand before driving, then recheck the mounts after the first drive on rough ground.

  • Measure both sides of the rear axle
  • Inspect springs and hangers at the same time

Specifications

Brand Pro Comp Suspension
Part number EXPPR2082
Shock series PRO-M
Position Rear
Extended length 22.3 in
Collapsed length 14.2 in
Upper and lower mount Loop
Lift 0 to 1 in
Finish Silver powder coat

Vehicle fitment

It fits the 2000 to 2006 Toyota Tundra in Base, Limited and SR5 trims.

It fits 2000 to 2006 Tundra models only, so confirm your vehicle’s year, model and trim before ordering.

Installation notes

Compare the 22.3 inch extended and 14.2 inch collapsed lengths with the rear shock being replaced before the Tundra is loaded. The 0 to 1 inch lift range is the one this shock is designed for. Loop mounts at both ends should line up with the factory brackets, and the 2 inch body should be checked for clearance at full compression.

The 0 to 1 inch lift range is narrow, so measure the Tundra’s rear height before ordering. Check the loop mounts line up with the factory brackets, and confirm the shock body clears the axle and frame at full compression. Test the damper by hand after installation to confirm smooth movement in both directions, and recheck the rear travel after the first drive on rough ground.

Confirm the rear shock clears the frame and the leaf springs at full droop, and check that the mounts are seated in the factory brackets on the Tundra.

What’s included

One PRO-M rear monotube shock with polyurethane boot under part number EXPPR2082.

Fitment

VehicleYearsTrims
Toyota Tundra2000–2006Base, Limited, SR5

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Does the PR2082 fit a 2003 Toyota Tundra?

Yes. It fits the 2000 to 2006 Toyota Tundra, including 2003 models in Base, Limited and SR5 trims. Confirm the lift range on your truck before ordering.

Does it fit a 2010 Toyota Tundra?

No. The shock fits the 2000 to 2006 Tundra only, so a 2010 model falls outside the years it covers. Confirm your vehicle's year, model and trim before ordering.

What lift is the PR2082 for?

It is designed for 0 to 1 inch of lift. The shock has a 22.3 inch extended length, a 14.2 inch collapsed length and a 2 inch body. Measure the lift on your Tundra before ordering.

Can the rear shock be swapped without removing the springs?

In many cases the shock can be removed from its mounts without taking the springs out. Support the axle with a jack, remove the fasteners, and check that the new unit fits the same mount points before tightening.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon