Select your vehicle
-13%

Pro Comp 2.5″ PRO-VST Rear Shocks – 57030BX-2

Pro Comp Suspension

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Fits the 2007–2021 Toyota Tundra, including the 1794 Edition and TRD Pro
  • Rear position, 2.5-inch gas-charged monotube shock
  • Hard-anodized, thick-wall impact forged body
  • 17-4 PH stainless steel shaft, chrome plated
  • Part number EXP57030BX-2 (model 57030BX-2)

Description

Overview

The Pro Comp PRO-VST 2.5-inch rear shock, part EXP57030BX-2 (model 57030BX-2), is a gas-charged monotube shock for the rear of the vehicle. It is a direct fit for the 2007–2021 Toyota Tundra.

The PRO-VST is built for rough off-road use. Its body is a hard-anodized, thick-wall impact forged 2.5-inch tube. The hard anodizing reduces friction and bore wear inside the body, which helps the damping hold up under repeated hard use. The shaft is 17-4 PH stainless steel, precipitation hardened and chrome plated for corrosion and abrasion resistance. Vehicle Specific Tuning is applied to each PRO-VST shock so the damping suits the vehicle it is sold for, with on-road ride quality as well as off-road control.

Key features

  • Gas-charged monotube design
  • Hard-anodized, thick-wall impact forged 2.5-inch body
  • 17-4 PH stainless steel shaft, chrome plated
  • Hard-anodized bore to reduce friction and wear
  • Vehicle Specific Tuning for each application
  • Rear position

Towing and rear shock load

Rear shocks and springs work as a system. The spring carries the weight, while the shock controls how fast the spring compresses and rebounds. When a truck carries heavy loads or pulls a trailer, repeated compression can heat and fade a worn shock, which makes the rear end feel loose on the highway. A gas-charged design helps the damping stay consistent when the shock works hard over long stretches.

Before adding shocks to a towing setup, check the rear springs for sag, the bump stops for wear, and the mounting bushings for cracks. A new shock on tired springs can bottom out sooner, so inspect the whole rear suspension together. Keeping the shock body clean and checking for leaks after long trips helps catch early wear.

  • Check rear springs for sag or cracks
  • Inspect bump stops for wear
  • Look for oil on the shock body after long trips
  • Replace shocks in pairs on the same axle

Specifications

Brand Pro Comp Suspension
Part number EXP57030BX-2
Series PRO-VST
Position Rear
Shock type Monotube
Gas charge Gas charged
Body diameter 2.5 in
Body Hard-anodized, impact forged
Shaft 17-4 PH stainless steel, chrome plated

Vehicle fitment

It fits the 2007–2021 Toyota Tundra across the 1794 Edition, Base, Limited, Nightshade, Platinum, SR, SR5, TRD Pro and Trail versions. Years outside 2007–2021 are not covered, and no other Toyota model applies.

Years outside 2007–2021 are not on the list, and no other Toyota model is named. Confirm your vehicle’s year, model and trim before ordering.

What’s included

One PRO-VST rear shock. No boot, bushing or hardware is described, so none is listed here.

Fitment

VehicleYearsTrims
Toyota Tundra2007–20211794 Edition, Base, Limited, Nightshade, Platinum, SR, SR5, TRD Pro, Trail

Use “Select your vehicle” at the top of the page to check this part against your vehicle.

Questions & Answers

Will the Pro Comp EXP57030BX-2 fit a 2010 Toyota Tundra?

Yes. It fits the 2007–2021 Toyota Tundra, so a 2010 Tundra falls within that range. Confirm your trim before ordering, since several Tundra versions are covered.

Is the EXP57030BX-2 a gas-charged shock?

Yes. It is a gas-charged monotube design with a 2.5-inch body, and it belongs to Pro Comp's PRO-VST series for vehicle specific tuning.

What shaft material does the PRO-VST use?

The shaft is 17-4 PH stainless steel. It is precipitation hardened and chrome plated, which Pro Comp says gives corrosion and abrasion resistance for off-road use.

Is this a rear shock?

Yes. It is listed in the rear position, with a hard-anodized, impact forged body built for off-road use. Pro Comp's series name is PRO-VST, and it is sold as the 57030BX-2 model.

Should rear shocks be replaced along with rear springs?

Often yes. Shocks and springs share the load, and an older shock can wear quickly on a new spring. Inspect the shock for leaks and check the bushings before deciding. Replacing both at the same time keeps ride height and damping consistent across the rear axle.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon