Select your vehicle
-13%

G2 Toyota 7.5 Inch Tacoma Front Master Ring and Pinion Installation Kit – 35-2055

G2 Axle and Gear

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Master kit with bearings for the Toyota 7.5-inch IFS (Tacoma) axle, front
  • For use in Toyota 7.5-inch IFS non clam shell front axle
  • Includes Timken pinion bearings and carrier bearings, shims, nut, seal and crush sleeve
  • Gear marking compound, thread locking compound and silicone sealer

Description

Overview

The G2 Axle and Gear 35-2055 is a master ring and pinion installation kit with bearings for the Toyota 7.5-inch IFS (Tacoma) axle, for the front axle position.

The 35-2055 includes the parts needed to install a ring and pinion, with pinion and carrier bearings along with the shims, nut, seal and compounds. Some of its parts are hard-to-find items that auto parts stores rarely stock. It is for the Toyota 7.5-inch IFS non clam shell front axle. The ring and pinion gear set is not included.

Key features

  • Master kit with bearings for the Toyota 7.5-inch IFS (Tacoma) axle
  • Timken outer and inner pinion bearings and races
  • Pinion shims and carrier shims
  • Carrier bearings and races included
  • Pinion nut, crush sleeve, pinion seal and ring gear bolts
  • Thread locking compound, gear marking compound and silicone sealer
  • For use in Toyota 7.5-inch IFS non clam shell front axle

Front axle rebuild considerations

A front IFS gear set works under different loads than a rear axle, and front wear often shows up as vibration or uneven tire wear tied to steering and drive. During a rebuild, check the front differential for play in the carrier, and inspect the pinion bearing for roughness before reusing any part of the old setup.

Because the front ring and pinion turns with the steering and drive shafts, clean seals and a correct breather matter. Use fresh gear oil, and keep the seal surfaces free of old sealant before applying the new compound. A clean, measured rebuild is easier to keep quiet on the road than one that was rushed.

  • Replace front axle seals during the same service
  • Check the drive flange surface for scoring
  • Keep a record of shim thickness for each side

Specifications

Brand G2 Axle and Gear
Part number 35-2055
UPC 631410096040
Product type Master ring and pinion installation kit with bearings
Axle Toyota 7.5-inch IFS (Tacoma)
Axle location Front
Popular axle manufacturer Toyota
Kit type Master kit with bearings
Listing condition For use in Toyota 7.5-inch IFS non clam shell front axle
Contents Pinion nut, pinion seal, Timken outer pinion bearing and race, crush sleeve, Timken inner pinion bearing and race, pinion shims, carrier shims, carrier bearings and races, ring gear bolts, thread locking compound, gear marking compound, silicone sealer

Vehicle fitment

The 35-2055 is identified by axle rather than by vehicle: it is made for the Toyota 7.5-inch IFS (Tacoma) axle in the front position, for the non clam shell front axle. Confirm fit for your vehicle’s year, model and trim before ordering.

This kit is made only for the Toyota 7.5-inch IFS non clam shell front axle and is not designed for other axle designs or sizes. Confirm fit for your vehicle’s year, model and trim before ordering.

Installation notes

A master kit such as the 35-2055 rebuilds the gear setup completely, so the bearings are replaced along with the gear set. The pinion shims, carrier shims, crush sleeve and gear marking compound in the 35-2055 are the parts used to set pinion depth, preload and the tooth contact pattern, which calls for an installer with gear setup experience and a careful break-in afterwards.

What’s included

  • Pinion nut
  • Pinion seal
  • Timken outer pinion bearing and race
  • Crush sleeve
  • Timken inner pinion bearing and race
  • Pinion shims
  • Carrier shims
  • Carrier bearings and races
  • Ring gear bolts
  • Thread locking compound
  • Gear marking compound
  • Silicone sealer

Not included with the 35-2055: ring and pinion gear set.

SKU: G/235-2055 Category:

Specification

Shipping weight 20.00 lbs
Package dimensions 12.90 × 12.80 × 3.10 in
brands

Questions & Answers

What axle is the G2 35-2055 for?

The 35-2055 is a master installation kit with bearings for the Toyota 7.5-inch IFS (Tacoma) axle. The 35-2055 listing gives the axle location as front. The 35-2055 is described by axle and does not replace the ring and pinion gear set.

What is included in the G2 35-2055 kit?

The 35-2055 kit includes pinion nut, pinion seal, Timken outer pinion bearing and race, crush sleeve, Timken inner pinion bearing and race, pinion shims, carrier shims, carrier bearings and races, ring gear bolts, thread locking compound, gear marking compound and silicone sealer.

Does the 35-2055 include the ring and pinion gears?

No. Only the installation parts and bearings are in the box, so the ring and pinion gears need to be purchased on their own.

Is the 35-2055 for a clam shell front axle?

No. The kit is made for the Toyota 7.5-inch IFS non clam shell front axle, which is the front axle of the Tacoma, so clam shell designs are outside its fit.

How do I know whether the front axle needs a full ring and pinion rebuild?

Look for noise on drive or coast, uneven contact on the teeth when checked with marking compound, and play at the pinion. Front gear wear often shows up with tire wear or vibration, so check the set when the front axle is opened for service.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon