Select your vehicle
-13%

G2 Ford 8.8 Inch IFS Master Ring and Pinion Installation Kit – 35-2088

G2 Axle and Gear

$120.00In stock
Buy on Amazon

See similar parts on Amazon

Price and availability as of Nov 18, 2026 8:10 PM MST, from Amazon.com, and subject to change. The Amazon listing has the current details.

Check out with your Amazon account. Amazon handles delivery and returns.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • For 1997 and up Ford F-150 8.8 inch IFS front axles only
  • Timken pinion and carrier bearings with races
  • Shims, crush sleeve, pinion seal and nut
  • Part number 35-2088

Description

Overview

The G2 Axle and Gear 35-2088 is a master ring and pinion installation kit for the Ford 8.8 Inches IFS front axle.

The 35-2088 is the master kit for the independent front differential of the Ford F-150. It supplies Timken pinion and carrier bearings with races, shim sets, a crush sleeve, a nut and seal, ring gear bolts, and sealing and marking compounds for the gear swap.

The independent front differential in the Ford F-150 is covered by G2’s 35-2088 for 1997 and later trucks. The master kit’s Timken bearings with races, pinion and carrier shims, crush sleeve, nut and seal, ring gear bolts and sealing and marking compounds let the installer replace every part that wears at the gear mesh of the Ford 8.8 inch IFS unit.

Key features

  • Master installation kit for the Ford 8.8 Inches IFS axle (front)
  • Includes pinion Nut
  • Includes pinion Seal
  • Includes Timken Outer Pinion Bearing and Race
  • Includes crush Sleeve
  • Includes Timken Inner Pinion Bearing and Race
  • Includes pinion Shims
  • Includes carrier Shims
  • Includes carrier Bearings and Races
  • Includes ring Gear Bolts

Front differential service tips

The IFS unit is compact, so access is tight and small mistakes are easy to make. Pulling the differential is usually the easiest way to reach the pinion and carrier. Clean the housing thoroughly before any new parts go in, because stray debris can ride on fresh bearings and gears and cause early wear.

Setup follows the familiar pattern. Use the shims to set pinion depth, tighten the crush sleeve gradually while checking preload, and read the contact with marking compound. Small shim changes move the pattern a noticeable amount, so make adjustments in small steps and check after each one.

  • Plan the job with the differential out
  • Use a torque wrench on the pinion nut
  • Replace axle seals while the housing is open

Specifications

Brand G2 Axle and Gear
Part number 35-2088
UPC 631410096095
Kit type Master kit with bearings
Axle location Front
Axle type Ford 8.8 Inches IFS
Axle manufacturer Ford

Vehicle fitment

It fits 1997 and later Ford F-150 IFS front axles, which are Ford 8.8 inch front units. Rear 8.8 inch axles use a different kit.

Confirm your vehicle’s axle type, spline count and year before ordering.

Installation notes

The IFS housing is compact, so the pinion and carrier work is best done with the differential removed. Use the shims for depth, set the crush sleeve and read the pattern with compound.

Before opening the Ford 8.8 Inches IFS housing for the 35-2088 job, gather a dial indicator, a torque wrench and clean gear oil. Record the original gear pattern, because the 35-2088 shims are the tool for moving the new pattern toward it. Fit the new nut and seal. Sort shims by thickness.

What’s included

  • Pinion Nut
  • Pinion Seal
  • Timken Outer Pinion Bearing and Race
  • Crush Sleeve
  • Timken Inner Pinion Bearing and Race
  • Pinion Shims
  • Carrier Shims
  • Carrier Bearings and Races
  • Ring Gear Bolts
  • Thread Locking Compound
  • Gear Marking Compound
  • Silicone Sealer

Not included: ring and pinion gears; the 35-2088 supplies installation parts for the Ford 8.8 Inches IFS axle only.

SKU: G/235-2088 Category:

Specification

Shipping weight 13.00 lbs
Package dimensions 12.90 × 12.80 × 3.10 in
brands

Questions & Answers

What axle does the 35-2088 kit fit?

It fits 1997 and later Ford F-150 IFS front axles, the Ford 8.8 inch IFS. Rear 8.8 inch axles need another kit.

What is included in the 35-2088 kit?

Contents are a pinion nut, seal, crush sleeve, Timken inner and outer pinion bearings with races, pinion shims, carrier shims, carrier bearings and races, ring gear bolts, thread locker, marking compound and silicone sealer.

Does the 35-2088 include the gears?

No. It is for IFS front axles only. The Ford 8.8 inch rear axle uses 35-2013 or 25-2013. Confirm fit for your axle type before ordering.

Should the axle shafts be inspected during this job?

Yes, while the front differential is out. Check the axle shafts, U-joints or CV boots for wear and damage, since they are easier to reach at this stage. Replacing worn parts now saves a second teardown.

Why does the IFS housing need to be clean?

Debris in the housing can ride on new bearings and gears and cause early wear. Wipe down the housing and magnet, and flush old fluid before measuring pinion depth and reading the pattern.

Ready to order?

Order this part on Amazon and check out with your Amazon account. Amazon handles delivery and returns.

Buy on Amazon