Overview
The G2 Axle and Gear 4-XJ3-488M is a 4.88 ring and pinion gear set with front and rear minor installation kits for the 1996–2001 Jeep Cherokee XJ. The kit pairs a 4.88 front gear set for the Dana 30 short front axle with a 4.88 rear gear set for the Dana 35 rear axle, so both axles of the Jeep are regeared in one kit.
For the 4-XJ3-488M, G2 describes its complete ring and pinion kits as including everything needed for a gear swap: front and rear gear sets plus the minor installation kits for both axles. The 4-XJ3-488M gives Cherokee XJ owners a 4.88 option for changing axle gearing, and G2 says its gears are engineered for oversized tires and high performance engines.
Key features
- Complete front and rear set: 4.88 ring and pinion gear sets for both axles plus matched minor installation kits
- Built for the Dana 30 short front axle and the Dana 35 rear axle
- Computer heat treated 8620 steel gears
- Manufactured to O.E. specifications.
- Double shot peened and double lapped gear sets
- Limited lifetime warranty listed by G2
- It fits front axles with a 3.73 and up carrier and rear axles with a 3.54 and up carrier.
Checking the carrier fit
Carrier type decides what gear sets will fit inside an axle, so confirm the carrier on the front and rear axles before ordering. Carriers with different bearing and bolt layouts cannot be swapped freely, even when the ratio matches. A quick inspection of the axle tag, the differential cover and the carrier casting can save a return.
Regearing a Cherokee XJ is also a good moment to inspect the rest of the driveline. Pinion seals, output shaft seals, u-joints and the driveshaft yokes often show wear that is easier to fix while the axles are open. Check the axle fluid for metal particles, since fine debris can point to a gear or bearing already in trouble.
- Confirm both carriers before buying gears
- Replace pinion and axle seals while the axles are open
- Look for metal particles in the axle fluid
- Recheck fluid and fasteners after the first drives
Specifications
| Brand | G2 Axle and Gear |
|---|---|
| Part number | 4-XJ3-488M |
| UPC | 631410141405 |
| Product type | Ring and pinion gear sets with front and rear minor installation kits |
| Gear ratio | 4.88 |
| Vehicle named in listing | 1996–2001 Jeep Cherokee XJ |
| Front axle | Dana 30 short (3.73 and up carrier) |
| Rear axle | Dana 35 (3.54 and up carrier) |
| Axle location | Front and rear |
| Kit type | Minor kit |
| Gear material | Computer heat treated 8620 steel |
| Finishing | Double shot peened, double lapped |
| Manufacturing | Manufactured to O.E. specs |
| Warranty | Limited lifetime warranty |
Vehicle fitment
It fits the 1996–2001 Jeep Cherokee XJ and is built for a Dana 30 short front axle (3.73 and up carrier) and a Dana 35 rear axle (3.54 and up carrier). Confirm fit for your vehicle’s year, model and trim before ordering.
The 4-XJ3-488M listing does not cover Cherokee XJ model years outside 1996–2001, other Cherokee generations such as the SJ and KL, and the Grand Cherokee. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
Fitting the 4-XJ3-488M changes the gear ratio on both axles of a Cherokee XJ, which is work for an experienced gear installer. The two minor installation kits in the 4-XJ3-488M are the parts used for setting the new gears, and the same 4.88 ratio goes in both axles so the drivetrain stays matched. The 4-XJ3-488M is a minor kit, and bearing sets are not among its listed contents. Plan a careful break-in for the new 4-XJ3-488M gears after installation.
What’s included
- Front ring and pinion gear set, 4.88
- Rear ring and pinion gear set, 4.88
- Front minor installation kit
- Rear minor installation kit




