Select your vehicle

G2 GM 8.6 Inch 99 and 08 Master Ring and Pinion Installation Kit – 35-2022

G2 Axle and Gear

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • For 1999-2008 GM 8.6 inch (10 bolt) rear axles
  • Timken pinion bearings plus carrier bearings and races
  • Shims, crush sleeve, pinion seal and ring gear bolts
  • Part number 35-2022

Description

Overview

The G2 Axle and Gear 35-2022 is a master ring and pinion installation kit for the GM 10 Bolt 8.6 Inches rear axle.

Part 35-2022 gathers what a GM 10 Bolt 8.6 inch rear axle needs when its gears are replaced. Inside are Timken inner and outer pinion bearings, carrier bearings and races, a crush sleeve, pinion seal and nut, shim packs for pinion and carrier, new ring gear bolts, and sealing and marking compounds.

The 8.6 inch GM axle has a 10 bolt cover and a compact carrier, and its gear set depends on correct shimming. This G2 master kit puts the bearings, races, shims and fasteners in the same box, which saves hunting for sizes. The thread locker secures the ring gear bolts, the sealer closes the cover and the crush sleeve sets pinion preload as the nut is tightened.

Key features

  • Master installation kit for the GM 10 Bolt 8.6 Inches axle (rear)
  • Includes pinion Nut
  • Includes pinion Seal
  • Includes Timken Outer Pinion Bearing and Race
  • Includes crush Sleeve
  • Includes Timken Inner Pinion Bearing and Race
  • Includes pinion Shims
  • Includes carrier Shims
  • Includes carrier Bearings and Races
  • Includes ring Gear Bolts

8.6 inch axle setup notes

The 8.6 inch GM rear axle uses a compact carrier and a 10 bolt cover, so access to the gears is tighter than on larger axles. Careful work with the shims and crush sleeve matters because the carrier leaves less room for error. Keep the cover bolts clean and torque them evenly when reassembling.

Pinion depth is the first setting to make, followed by carrier preload and backlash. Each change shifts the gear pattern, so re-mark and recheck after every adjustment. A consistent pattern across the drive and coast sides usually means the set is ready for final torque.

Common wear items beyond the gears include the axle seals and the pinion yoke seal. Inspect them when the cover is off, because a leak at either spot can contaminate new gears. Use the correct gear oil for the axle and fill it to the level the axle calls for.

  • Re-mark the pattern after each shim change
  • Replace any seal found worn

Specifications

Brand G2 Axle and Gear
Part number 35-2022
UPC 631410095685
Kit type Master kit with bearings
Axle location Rear
Axle type GM 10 Bolt 8.6 Inches
Axle manufacturer GM

Vehicle fitment

It is a master kit for 1999-2008 GM 8.6 inch rear axles with the 10 bolt design. Confirm your rear axle is an 8.6 inch 10 bolt before choosing it, and confirm the axle type, spline count and year before ordering.

Confirm your vehicle’s axle type, spline count and year before ordering.

Installation notes

Pinion depth and preload on an 8.6 inch axle are set with the supplied shims and the crush sleeve. Brush on the marking compound, rotate the gears and read the pattern; adjust shims until the contact is right.

Before opening the GM 10 Bolt 8.6 Inches housing for the 35-2022 job, gather a dial indicator, a torque wrench and clean gear oil. Record the original gear pattern, because the 35-2022 shims are the tool for moving the new pattern toward it. Fit the new nut and seal. Sort shims by thickness.

What’s included

  • Pinion Nut
  • Pinion Seal
  • Timken Outer Pinion Bearing and Race
  • Crush Sleeve
  • Timken Inner Pinion Bearing and Race
  • Pinion Shims
  • Carrier Shims
  • Carrier Bearings and Races
  • Ring Gear Bolts
  • Thread Locking Compound
  • Gear Marking Compound
  • Silicone Sealer

Not included: ring and pinion gears; the 35-2022 supplies installation parts for the GM 10 Bolt 8.6 Inches axle only.

SKU: G/235-2022 Category:

Specification

Shipping weight 6.15 lbs
Package dimensions 12.00 × 11.00 × 3.00 in
brands

Questions & Answers

What axle does the 35-2022 kit fit?

It is for GM 10 Bolt 8.6 inch rear axles built 1999-2008. Check the axle tag or housing to confirm the size before ordering.

What is included in the 35-2022 kit?

The kit contains a pinion nut, pinion seal, crush sleeve, Timken inner and outer pinion bearings with races, pinion and carrier shims, carrier bearings and races, ring gear bolts, thread locker, marking compound and silicone sealer.

Does the 35-2022 include the gears?

No. The kit contains installation parts only, so a matching 8.6 inch ring and pinion set needs to be bought separately.

Can a 10 bolt 8.6 inch axle be upgraded with a different ring gear?

Ring gears are sized to the carrier, so a different ring and pinion must match the 8.6 inch housing. Check the ring gear size and pinion mounting before ordering. Replacing gears in a matched set keeps the tooth contact predictable.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon