Overview
The G2 Axle and Gear 4-TJ2-456M is a 4.56 ring and pinion gear set with front and rear minor installation kits for the 1997–2006 Jeep Wrangler TJ and LJ. The kit pairs a 4.56 front gear set for the Dana 30 front axle with a 4.56 rear gear set for the Dana 44 rear axle, so both axles of the Jeep are regeared in one kit.
The 4-TJ2-456M is a complete ring and pinion kit with everything needed for a gear swap: front and rear gear sets plus the minor installation kits for both axles. It gives Wrangler TJ and LJ owners a 4.56 option for changing axle gearing, and the gears are designed for oversized tires and high performance engines. The kit is for non-Rubicon models.
Key features
- Complete front and rear set: 4.56 ring and pinion gear sets for both axles plus matched minor installation kits
- Built for the Dana 30 front axle and the Dana 44 rear axle
- Computer heat treated 8620 steel gears
- Manufactured to O.E. specifications
- Double shot peened and double lapped gear sets
- Limited lifetime warranty listed by G2
- For non-Rubicon models
Planning a gear swap
A ring and pinion swap is more than replacing two gear sets. The pinion depth, bearing preload and backlash all have to be set within the correct range, and the work is usually done by an experienced gear installer. Bearing sets are not among the included parts, so check the carrier bearings and pinion bearings before ordering, and replace any that show wear.
Larger tires and a gear change are often done together, because a numerically higher ratio helps the engine pull the heavier setup. After installation, plan a careful break-in: keep throttle use moderate and avoid heavy towing for the first stretch of miles, then recheck the gear oil level and look for leaks.
- Check carrier and pinion bearings before ordering
- Confirm axle types before choosing the kit
- Replace the gear oil after installation
Specifications
| Brand | G2 Axle and Gear |
|---|---|
| Part number | 4-TJ2-456M |
| UPC | 631410141214 |
| Product type | Ring and pinion gear sets with front and rear minor installation kits |
| Gear ratio | 4.56 |
| Vehicle named in listing | 1997–2006 Jeep Wrangler TJ and LJ |
| Front axle | Dana 30 |
| Trim note | Non-Rubicon models |
| Rear axle | Dana 44 |
| Axle location | Front and rear |
| Kit type | Minor kit |
| Gear material | Computer heat treated 8620 steel |
| Finishing | Double shot peened, double lapped |
| Manufacturing | Manufactured to O.E. specs |
| Warranty | Limited lifetime warranty |
Vehicle fitment
The 4-TJ2-456M is for the 1997–2006 Jeep Wrangler TJ and LJ with a Dana 30 front axle and a Dana 44 rear axle. Confirm your vehicle’s year, model and trim before ordering, and check that its axles are a Dana 30 front and Dana 44 rear.
The 4-TJ2-456M listing does not cover the earlier Wrangler YJ (1987–1995), the Wrangler JK (2007–2018) and the Wrangler JL (2018–2022). Confirm your vehicle’s year, model and trim before ordering.
Installation notes
Fitting the 4-TJ2-456M changes the gear ratio on both axles of a Wrangler TJ and LJ, which is work for an experienced gear installer. The two minor installation kits in the 4-TJ2-456M are the parts used for setting the new gears, and the same 4.56 ratio goes in both axles so the drivetrain stays matched. The 4-TJ2-456M is a minor kit, and bearing sets are not among its listed contents. Plan a careful break-in for the new 4-TJ2-456M gears after installation.
What’s included
- Front ring and pinion gear set, 4.56
- Rear ring and pinion gear set, 4.56
- Front minor installation kit
- Rear minor installation kit





