Overview
The G2 Axle and Gear 4-XJ3-456M is a 4.56 ring and pinion gear set with front and rear minor installation kits for the 1996–2001 Jeep Cherokee XJ. The kit pairs a 4.56 front gear set for the Dana 30 short front axle with a 4.56 rear gear set for the Dana 35 rear axle, so both axles of the Jeep are regeared in one kit.
For the 4-XJ3-456M, G2 describes its complete ring and pinion kits as including everything needed for a gear swap: front and rear gear sets plus the minor installation kits for both axles. The 4-XJ3-456M gives Cherokee XJ owners a 4.56 option for changing axle gearing, and G2 says its gears are engineered for oversized tires and high performance engines.
Key features
- Complete front and rear set: 4.56 ring and pinion gear sets for both axles plus matched minor installation kits
- Built for the Dana 30 short front axle and the Dana 35 rear axle
- Computer heat treated 8620 steel gears
- Manufactured to O.E. specs.
- Double shot peened and double lapped gear sets
- Limited lifetime warranty listed by G2
- The front gears suit the 3.73 and up carrier, and the rear gears suit the 3.54 and up carrier.
Before a gear swap
Changing ring and pinion gearing alters how the engine, transmission and axles share the load, so the whole drivetrain should be checked before the new gears go in. Inspect the pinion depth, backlash and pinion bearing preload, and confirm the carrier parts are clean and undamaged.
Because the front and rear ratios affect each other, most owners change both axles at the same time. Matching ratios keeps the wheels turning at the same rate and reduces stress on the driveline. Larger tires also change effective gearing, so plan the swap around the tires you run.
- Inspect pinion bearings and seals before installing
- Check backlash and contact pattern after assembly
- Replace worn axle bearings and seals as needed
- Break in new gears gradually
Specifications
| Brand | G2 Axle and Gear |
|---|---|
| Part number | 4-XJ3-456M |
| UPC | 631410141399 |
| Product type | Ring and pinion gear sets with front and rear minor installation kits |
| Gear ratio | 4.56 |
| Vehicle named in listing | 1996–2001 Jeep Cherokee XJ |
| Front axle | Dana 30 short (3.73 and up carrier) |
| Rear axle | Dana 35 (3.54 and up carrier) |
| Axle location | Front and rear |
| Kit type | Minor kit |
| Gear material | Computer heat treated 8620 steel |
| Finishing | Double shot peened, double lapped |
| Manufacturing | Manufactured to O.E. specs |
| Warranty | Limited lifetime warranty |
Vehicle fitment
It fits the 1996–2001 Jeep Cherokee XJ, also called the 96-01 XJ Cherokee. It applies to a Jeep with Dana 30 short front and Dana 35 rear axles. Confirm fit for your vehicle’s year, model and trim before ordering.
The 4-XJ3-456M listing does not cover Cherokee XJ model years outside 1996–2001, other Cherokee generations such as the SJ and KL, and the Grand Cherokee. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
Fitting the 4-XJ3-456M changes the gear ratio on both axles of a Cherokee XJ, which is work for an experienced gear installer. The two minor installation kits in the 4-XJ3-456M are the parts used for setting the new gears, and the same 4.56 ratio goes in both axles so the drivetrain stays matched. The 4-XJ3-456M is a minor kit, and bearing sets are not among its listed contents. Plan a careful break-in for the new 4-XJ3-456M gears after installation.
What’s included
- Front ring and pinion gear set, 4.56
- Rear ring and pinion gear set, 4.56
- Front minor installation kit
- Rear minor installation kit







