Overview
The G2 Axle and Gear 4-XJ-410M is a 4.10 ring and pinion gear set with front and rear minor installation kits for the 1984–2001 Jeep Cherokee XJ. The kit pairs a 4.10 front gear set for the Dana 30 reverse front axle with a 4.10 rear gear set for the Dana 35 rear axle, so both axles of the Jeep are regeared in one kit.
For the 4-XJ-410M, G2 describes its complete ring and pinion kits as including everything needed for a gear swap: front and rear gear sets plus the minor installation kits for both axles. The 4-XJ-410M gives Cherokee XJ owners a 4.10 option for changing axle gearing, and G2 says its gears are engineered for oversized tires and high performance engines.
Key features
- Complete front and rear set: 4.10 ring and pinion gear sets for both axles plus matched minor installation kits
- Built for the Dana 30 reverse front axle and the Dana 35 rear axle
- Computer heat treated 8620 steel gears
- Manufactured to O.E. specifications.
- Double shot peened and double lapped gear sets
- Limited lifetime warranty listed by G2
- Carrier fit: front 3.73 and up carrier; rear 3.54 and up carrier
Gear ratio and driving feel
Changing from a stock ratio to 4.10 alters engine speed at a given road speed, so the truck feels quicker off the line and turns more engine revolutions at highway speed. Taller tires offset this effect, and a lower ratio can make a truck with larger tires feel more relaxed. Think about how the vehicle is used before committing to a ratio change.
Regearing usually involves related parts. Bearings, seals and axle fluid are often replaced when the gears come out, and the speedometer may need recalibration after a ratio change. Check the axle bearings and pinion seal during the install, since they are easier to replace while the axle is open.
- Consider tire size before choosing a ratio
- Plan for fresh axle fluid after the swap
- Recalibrate the speedometer if the reading changes
- Inspect axle bearings while the axles are open
Specifications
| Brand | G2 Axle and Gear |
|---|---|
| Part number | 4-XJ-410M |
| UPC | 631410141320 |
| Product type | Ring and pinion gear sets with front and rear minor installation kits |
| Gear ratio | 4.10 |
| Vehicle named in listing | 1984–2001 Jeep Cherokee XJ |
| Front axle | Dana 30 reverse (3.73 and up carrier) |
| Rear axle | Dana 35 (3.54 and up carrier); this axle is marked 4.11 |
| Axle location | Front and rear |
| Kit type | Minor kit |
| Gear material | Computer heat treated 8620 steel |
| Finishing | Double shot peened, double lapped |
| Manufacturing | Manufactured to O.E. specs |
| Warranty | Limited lifetime warranty |
Vehicle fitment
It fits the 1984–2001 Jeep Cherokee XJ (84-01 XJ Cherokee), with a Dana 30 reverse front axle and a Dana 35 rear axle. It applies to a Jeep fitted with those two axles.
The 4-XJ-410M listing does not cover Cherokee XJ model years outside 1984–2001, other Cherokee generations such as the SJ and KL, and the Grand Cherokee. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
Fitting the 4-XJ-410M changes the gear ratio on both axles of a Cherokee XJ, which is work for an experienced gear installer. The two minor installation kits in the 4-XJ-410M are the parts used for setting the new gears, and the same 4.10 ratio goes in both axles so the drivetrain stays matched. The 4-XJ-410M is a minor kit, and bearing sets are not among its listed contents. Plan a careful break-in for the new 4-XJ-410M gears after installation.
What’s included
- Front ring and pinion gear set, 4.10
- Rear ring and pinion gear set, 4.10
- Front minor installation kit
- Rear minor installation kit







