Overview
The G2 Axle and Gear 4-XJ6-410M is a 4.10 ring and pinion gear set with front and rear minor installation kits for the 2000–2001 Jeep Cherokee XJ. The kit pairs a 4.10 front gear set for the Dana 30 short front axle with a 4.10 rear gear set for the Chrysler 8.25-inch rear axle, so both axles of the Jeep are regeared in one kit.
For the 4-XJ6-410M, G2 describes its complete ring and pinion kits as including everything needed for a gear swap: front and rear gear sets plus the minor installation kits for both axles. The 4-XJ6-410M gives Cherokee XJ owners a 4.10 option for changing axle gearing, and G2 says its gears are engineered for oversized tires and high performance engines.
Key features
- Complete front and rear set: 4.10 ring and pinion gear sets for both axles plus matched minor installation kits
- Built for the Dana 30 short front axle and the Chrysler 8.25-inch rear axle
- Computer heat treated 8620 steel gears
- Built to O.E. specs.
- Double shot peened and double lapped gear sets
- Limited lifetime warranty listed by G2
- Front carrier note: 3.73 and up carrier
Gear swap planning
A gear swap on both axles changes the ratio the engine works through, so the drivetrain has to be planned as one system. Keep the front and rear gears matched, and make sure the driveshafts can handle the new ratio. Check the tire diameter after any change to tire size, because the gearing and tires together set the feel on the trail and on the highway.
Gear work is best done on a bench with proper tools, and the setup should cover pinion depth, backlash and tooth contact. Clean the carrier and housing thoroughly before assembly, and use fresh gear oil at the correct fill level. Expect a break-in period as the new gears seat, and check the fluid after the first trips.
- Match front and rear gear sets to the same ratio
- Inspect the carrier and axle bearings before assembly
- Use fresh gear oil at the correct fill level
- Plan a gentle break-in period after installation
Specifications
| Brand | G2 Axle and Gear |
|---|---|
| Part number | 4-XJ6-410M |
| UPC | 631410141474 |
| Product type | Ring and pinion gear sets with front and rear minor installation kits |
| Gear ratio | 4.10 |
| Vehicle named in listing | 2000–2001 Jeep Cherokee XJ |
| Front axle | Dana 30 short (3.73 and up carrier) |
| Rear axle | Chrysler 8.25-inch |
| Axle location | Front and rear |
| Kit type | Minor kit |
| Gear material | Computer heat treated 8620 steel |
| Finishing | Double shot peened, double lapped |
| Manufacturing | Manufactured to O.E. specs |
| Warranty | Limited lifetime warranty |
Vehicle fitment
The kit fits the 2000–2001 Jeep Cherokee XJ. The front axle is a Dana 30 short (3.73 and up carrier) and the rear axle is a Chrysler 8.25-inch, so it suits a Jeep with those axles. Model years outside 2000–2001 are not covered, and neither are other Cherokee generations or the Grand Cherokee.
The 4-XJ6-410M listing does not cover Cherokee XJ model years outside 2000–2001, other Cherokee generations such as the SJ and KL, and the Grand Cherokee. Confirm your vehicle’s year, model and trim before ordering.
Installation notes
Fitting the 4-XJ6-410M changes the gear ratio on both axles of a Cherokee XJ, which is work for an experienced gear installer. The two minor installation kits in the 4-XJ6-410M are the parts used for setting the new gears, and the same 4.10 ratio goes in both axles so the drivetrain stays matched. The 4-XJ6-410M is a minor kit, and bearing sets are not among its listed contents. Plan a careful break-in for the new 4-XJ6-410M gears after installation.
What’s included
- Front ring and pinion gear set, 4.10
- Rear ring and pinion gear set, 4.10
- Front minor installation kit
- Rear minor installation kit





