Select your vehicle

G2 Ford 9 Inch 3.06 Inch Bore Master Ring and Pinion Installation Kit – 35-2011

G2 Axle and Gear

Shop on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Slickrock 4X4 is a participant in the Amazon Associates Program. As an Amazon Associate we earn from qualifying purchases.

  • Master kit with bearings for the Ford 9-inch, 3.06-inch bore axle, rear
  • For use with 3.06-inch bore case
  • Includes Timken pinion bearings and carrier bearings, shims, nut, seal and crush sleeve
  • Gear marking compound, thread locking compound and silicone sealer

Description

Overview

The G2 Axle and Gear 35-2011 is a master ring and pinion installation kit with bearings for the Ford 9-inch, 3.06-inch bore axle, used in the rear axle position.

The 35-2011 follows G2’s master kit approach: it includes the parts needed to install a ring and pinion, with pinion bearings and carrier bearings along with the shims, nut, seal and compounds. Some of these parts are hard to find and rarely stocked by auto parts stores. It is for use with a 3.06-inch bore case. The ring and pinion gear set itself is not included.

Key features

  • Master kit with bearings for the Ford 9-inch, 3.06-inch bore axle
  • Timken outer and inner pinion bearings and races
  • Timken pinion pilot bearing included
  • Carrier bearings and races included
  • Pinion nut, crush sleeve, pinion seal and ring gear bolts
  • Thread locking compound, gear marking compound and silicone sealer
  • For use with 3.06-inch bore case

Pilot bearing and pinion support

The pinion pilot bearing sits at the inner end of the pinion and supports the tip of the shaft as it turns. When the pinion is worn or the pilot seat is damaged, the new pinion can run slightly off center, which shows up as noise under load. Inspecting the pilot bore for scoring is a quick step that is easy to skip and worth doing before the new bearing goes in.

Heavier-duty 9-inch use, such as towing or larger tires, puts more load through the carrier and pinion, so the setup matters more. Reuse of the ring gear bolts is not advised, and thread locker should be applied only to clean threads. Re-check the carrier bearing preload after the first few drives, because the new bearings settle as they seat.

Specifications

Brand G2 Axle and Gear
Part number 35-2011
UPC 631410095517
Product type Master ring and pinion installation kit with bearings
Axle Ford 9-inch, 3.06-inch bore
Axle location Rear
Popular axle manufacturer Ford
Kit type Master kit with bearings
Listing condition For use with 3.06-inch bore case
Contents Pinion nut, pinion seal, Timken outer pinion bearing and race, crush sleeve, Timken inner pinion bearing and race, pinion shims, Timken pinion pilot bearing, carrier shims, carrier bearings and races, ring gear bolts, thread locking compound, gear marking compound, silicone sealer

Vehicle fitment

The 35-2011 is identified by axle rather than by vehicle: it is made for the Ford 9-inch, 3.06-inch bore axle in the rear position, for use with a 3.06-inch bore case. Fitment is set by the axle, so match your housing’s bore to the kit before buying.

The 35-2011 is made for this axle design and size only. Check that your housing has a 3.06-inch bore before ordering.

Installation notes

A master kit such as the 35-2011 rebuilds the gear setup completely, so the bearings are replaced along with the gear set. The pinion shims, carrier shims, crush sleeve and gear marking compound in the 35-2011 are the parts used to set pinion depth, preload and the tooth contact pattern, which calls for an installer with gear setup experience and a careful break-in afterwards.

What’s included

  • Pinion nut
  • Pinion seal
  • Timken outer pinion bearing and race
  • Crush sleeve
  • Timken inner pinion bearing and race
  • Pinion shims
  • Timken pinion pilot bearing
  • Carrier shims
  • Carrier bearings and races
  • Ring gear bolts
  • Thread locking compound
  • Gear marking compound
  • Silicone sealer

Not included with the 35-2011: ring and pinion gear set.

SKU: G/235-2011 Category:

Specification

Shipping weight 7.00 lbs
Package dimensions 12.90 × 12.80 × 3.10 in
brands

Questions & Answers

What axle is the G2 35-2011 for?

The 35-2011 is a master installation kit with bearings for the Ford 9-inch, 3.06-inch bore axle. The 35-2011 listing gives the axle location as rear. The 35-2011 is described by axle and does not replace the ring and pinion gear set.

What is included in the G2 35-2011 kit?

The 35-2011 kit includes pinion nut, pinion seal, Timken outer pinion bearing and race, crush sleeve, Timken inner pinion bearing and race, pinion shims, Timken pinion pilot bearing, carrier shims, carrier bearings and races, ring gear bolts, thread locking compound, gear marking compound and silicone sealer.

Does the 35-2011 include the ring and pinion gears?

No. The 35-2011 contains installation parts and bearings only. No ring and pinion gear set is part of the kit, so the gears must be sourced separately before assembly begins.

What case does the 35-2011 need?

The 35-2011 is for use with a 3.06-inch bore case on the rear Ford 9-inch axle. The kit includes a Timken pinion pilot bearing. Check your housing's bore before ordering.

Do I need to replace the ring gear bolts when rebuilding?

Usually yes. Ring gear bolts are tightened to a set torque and can stretch, so new bolts give a more reliable clamp on the carrier. Clean the threads and apply the thread locking compound from the kit before installing them.

Find it on Amazon

Compare current versions and compatible options on Amazon, then check out with your Amazon account.

Shop on Amazon