Overview
The G2 Axle and Gear 35-2046A is a master ring and pinion installation kit with bearings for the Ford 10.5-inch axle in the rear position.
The kit includes the parts needed to install a ring and pinion: pinion and carrier bearings, shims, nut, seal and compounds. Some parts are hard-to-find items that auto parts stores rarely stock. It is for use in 1999-up Ford Sterling rear axles with Ford 10.5-inch gears only, and it allows installation of 10.5-inch gears in a 10.25-inch axle housing. The ring and pinion gear set is not included.
Key features
- Master kit with bearings for the Ford 10.5-inch axle
- Timken outer and inner pinion bearings and races
- Pinion shims and carrier shims
- Carrier bearings and races included
- Pinion nut, crush sleeve, pinion seal and ring gear bolts
- Thread locking compound, gear marking compound and silicone sealer
- For use in 1999-up Ford Sterling rear axles
- Must be used with Ford 10.5-inch gears only
- Allows installation of 10.5-inch gears in a 10.25-inch axle housing
Gear setup basics
Setting up a ring and pinion means balancing pinion depth, bearing preload and backlash so the teeth mesh with a steady contact pattern. Shims control depth and preload, while the crush sleeve sets preload as the pinion nut is tightened. Gear marking compound shows where the teeth touch so adjustments can be made before the axle goes back into service.
Because the bearings are replaced along with the gears, a rebuild is a good time to inspect the carrier, the case bearing bores and the axle seals. A break-in period with gentle driving helps the new surfaces settle, and checking the gear mesh again after the first few hundred miles of use is a reasonable habit.
- Confirm the axle housing matches the gear size
- Check the carrier and bearing bores for wear
- Re-check the pinion nut and bolts after break-in
Specifications
| Brand | G2 Axle and Gear |
|---|---|
| Part number | 35-2046A |
| UPC | 631410095968 |
| Product type | Master ring and pinion installation kit with bearings |
| Axle | Ford 10.5-inch |
| Axle location | Rear |
| Popular axle manufacturer | Ford |
| Kit type | Master kit with bearings |
| Listing condition | For use in 1999-up Ford Sterling rear axles |
| Listing condition | Must be used with Ford 10.5-inch gears only |
| Listing condition | Allows installation of 10.5-inch gears in a 10.25-inch axle housing |
| Contents | Pinion nut, pinion seal, Timken outer pinion bearing and race, crush sleeve, Timken inner pinion bearing and race, pinion shims, carrier shims, carrier bearings and races, ring gear bolts, thread locking compound, gear marking compound, silicone sealer |
Vehicle fitment
The 35-2046A is matched by axle rather than by vehicle. It is made for the Ford 10.5-inch axle in the rear position, for use in 1999-up Ford Sterling rear axles with Ford 10.5-inch gears only, and it allows 10.5-inch gears in a 10.25-inch axle housing. Confirm your vehicle’s year, model and trim before ordering.
It is not for other axle designs or sizes, so confirm the axle before buying.
Installation notes
A master kit such as the 35-2046A rebuilds the gear setup completely, so the bearings are replaced along with the gear set. The pinion shims, carrier shims, crush sleeve and gear marking compound in the 35-2046A are the parts used to set pinion depth, preload and the tooth contact pattern, which calls for an installer with gear setup experience and a careful break-in afterwards.
What’s included
- Pinion nut
- Pinion seal
- Timken outer pinion bearing and race
- Crush sleeve
- Timken inner pinion bearing and race
- Pinion shims
- Carrier shims
- Carrier bearings and races
- Ring gear bolts
- Thread locking compound
- Gear marking compound
- Silicone sealer
Not included with the 35-2046A: ring and pinion gear set.












